轮扣式钢管架支模工程讲义.docVIP

目 录 第一节、编制依据···············································1 第二节、工程概况···············································1 一、工程概况··················································1 二、支模方案··················································2 三、施工要求··················································4 第三节、施工计划···············································5 一、施工进度计划（每个施工段）·································5 二、材料与设备计划············································5 第四节、施工工艺技术···········································7 一、工艺流程··················································7 二、施工方法··················································8 三、检查验收··················································10 第五节、施工安全保证措施······································12 一、安全管理机构·············································12 二、安全措施·················································13 第六节、劳动力计划············································14 一、专业班组人员·············································14 二、专职安全生产管理人员······································15 第七节、计算书················································15 第一节、编制依据 1、《木结构设计规范》GB 50005-2003） 2、《建筑结构荷载规范》GB 50009-2001） 3、《混凝土结构设计规范》GB 50010-2002） 4、《钢结构设计规范》GB 50017-2003） 5、《建筑施工高处作业安全技术规范》JGJ 80-91） 6、《建筑施工承插型盘扣式钢管支架安全技术规范》（JGJ231-2010） 7、《建筑施工模板安全技术规范》JGJ 162-2008） 8、《建筑施工安全检查标准》（JGJ59-99） 9、《建设工程高大模板支撑系统施工安全监督管理导则》（建质[2009]254号） 10、全套施工图纸 11、施工组织设计 12、我司相关规定及作业指导书 第二节、工程概况 一、工程概况 工程名称： 工程规模：总建筑面积为约17283㎡。其中主要建筑单体如下： A区扩建厂房：框架结构1层，建筑面积为10233㎡； B区扩建厂房：框架结构1层，建筑面积为6883㎡（包含地下室1层2231㎡）； 仓库：框架结构1层，建筑面积为167㎡； 工程地址： 建设单位： 设计单位： 监理单位： 施工单位： 厂房、仓库简况： A区、B区厂房均为框架混凝土结构一层，层高7.5m，仓库为单层混凝土结构，层高4m，基础均采用静压预应力管桩（Φ500）基础，桩端持力层为强风化花岗岩，厂房单桩桩端承载力特征值qsa=4000kpa,仓库单桩桩端承载力特征值qsa=1800kpa；A区、B区厂房框架混凝土强度等级为C30，仓库框架混凝土强度等级为C25。 门窗分别采用铝合金门窗；内墙：采用白色乳胶漆；外墙采用外墙油漆；地面采用金刚砂地面。 砌体工程：非承重的均采用蒸压灰砂砖，外墙为180，内墙为100。墙体采用MU10、M7.5水泥砂浆砌筑。 二、支模方案 本方案编制未包括高大梁支模，高大梁支模另详见高大梁支模专项论证施工方案. （一）支模区域、支模高度、支模范围内的梁截面尺寸、跨度、板厚： 1）支模区域：A区厂房，搭设面积约10174m2。 支模高度：层高7.7m，支撑从底板标高-0.050m搭起，支模高度至标高7.650m，最大跨度：4.0m，板厚