说明书 CDH1 MP36336200A1XB1CGEMWW重载型液压缸设计 液压油缸设计论文【毕业论文+CAD图纸全套】.doc

宁XX大学 毕业设计(论文) CDH1 MP3/63/36/200A1X/B1CGEMWW 重载型液压缸设计 所在学院 专 业 班 级 姓 名 学 号 指导老师 年 月 日 摘 要 本液压油缸以传递动力为主，保证足够的动力是其基本要求。另外，还要考虑油缸的稳定性、可靠性、可维护性、安全性及效率。其中稳定是指系统工作时的运动平稳性及系统性能的稳定性(如环境温度对油液的影响等因素)。可靠性是指系统不因意外的原因而无法工作(如油管破裂、无电等情况)。可维护性是指系统尽可能简单，元件尽可能选标准件，结构上尽可能使维护方便．安全性是指不因液压缸的故障导致后车厢盖的其它事故．效率是指液压缸的各种能量损失尽可能的小。上述要求中，除满足系统的动力要求外，最重要的是保证系统的安全性和可靠性。 关键词：液压缸，油缸Abstract The hydraulic system to transfer power, ensure adequate power is its basic requirement. In addition, consider the system stability, reliability, maintainability, safety and efficiency. The stabilizing means when the system works steady motion and system performance stability (such as environmental temperature on the influence of oil etc). Reliability refers to the system is not due to accident reason to work ( such as tubing rupture without electricity, etc. ). Maintainability is referred to the system as simple as possible, element is chosen as far as possible standard parts, structure as much as possible so that the maintenance is convenient. Security is not due to the fault of the hydraulic system causes the antenna frame collapse or other accidents (such as the drop out of control, antenna due to gravity acceleration whereabouts ) . Efficiency refers to the hydraulic system of the various energy loss as small as possible. The above requirements, in addition to meet the power requirements, the most important thing is to ensure the safety and reliability of the system. Keywords: hydraulic system, 目 录 摘 要 II Abstract III 目 录 IV 1 油缸主参数的确定 5 2油缸主要部位的计算校核 9 2.1液压缸稳定性计算 9 2.2 缸筒的加工要求 10 2.3法兰设计 11 2.4(缸筒端部）法兰连接螺栓的强度计算 11 3 活塞的设计 13 4 导向套的设计与计算 14 5 端盖和缸底的设计与计算 16 6 缸体长度的确定 17 7 缓冲装置的设计 17 8 排气装置 18 9 密封件的选用 19 10 防尘圈 21 11 液压缸的安装连接结构 22 总 结 25 致 谢 26 参考文献 27 基本技术数据，是根据用途及结构类型来确定的，它反映了工作能力及特点，也基本上上确定了轮廓尺寸及本体总质量等。 1 油缸主参数的确定 本课题设计的油缸CDH1 MP3/63/36/200A1X/B1CGEMWW重载型液压缸设计重载型液压缸设计，查表 查得油缸的液压缸的内径为63mm,活塞杆直径为36mm,有效行程为200 mm 表4