MSP XX按键程序范例(附原理图)【DOC精选】.doc

下载文档

2
0
约 5页
2017-02-16 发布于江苏
举报
版权申诉
保障服务

MSP XX按键程序范例(附原理图)【DOC精选】.doc

1、本文档共5页，可阅读全部内容。
2、原创力文档（book118）网站文档一经付费（服务费），不意味着购买了该文档的版权，仅供个人/单位学习、研究之用，不得用于商业用途，未经授权，严禁复制、发行、汇编、翻译或者网络传播等，侵权必究。
3、本站所有内容均由合作方或网友上传，本站不对文档的完整性、权威性及其观点立场正确性做任何保证或承诺！文档内容仅供研究参考，付费前请自行鉴别。如您付费，意味着您自己接受本站规则且自行承担风险，本站不退款、不进行额外附加服务；查看《如何避免下载的几个坑》。如果您已付费下载过本站文档，您可以点击这里二次下载。
4、如文档侵犯商业秘密、侵犯著作权、侵犯人身权等，请点击“版权申诉”（推荐），也可以打举报电话：400-050-0827(电话支持时间：9:00-18:30)。

/117190815/blog/item/279b44c7332db1dbd1006008.html ＃i nclude msp430x14x.hvoid Init_Port(void){??? //将P1口所有的管脚在初始化的时候设置为输入方式??? P1DIR = 0;??? //将P1口所有的管脚设置为一般I/O口??? P1SEL = 0;??? ??? // 将P1.4 P1.5 P1.6 P1.7设置为输出方向??? P1DIR |= BIT4;??? P1DIR |= BIT5;P1DIR |= BIT6;??? P1DIR |= BIT7; //先输出低电平P1OUT = 0x00; // 将中断寄存器清零??? P1IE = 0;??? P1IES = 0;??? P1IFG = 0;??? //打开管脚的中断功能//对应的管脚由高到低电平跳变使相应的标志置位??? P1IE |= BIT0; ??? P1IES |= BIT0; ??? P1IE |= BIT1; ??? P1IES |= BIT1;P1IE |= BIT2; ??? P1IES |= BIT2; ??? P1IE |= BIT3; ??? P1IES |= BIT3;_EINT();//打开中断??? return;}void Delay(void){int i;for(i = 100;i--;i 0) ;//延时一点时间}int KeyProcess(void){??? int nP10,nP11,nP12,nP13;int nRes = 0;//P1.4输出低电平P1OUT = ~(BIT4);nP10 = P1IN BIT0;if (nP10 == 0) nRes = 13;nP11 = P1IN BIT1;if (nP11 == 0) nRes = 14;nP12 = P1IN BIT2;if (nP12 == 0) nRes = 15;nP13 = P1IN BIT3;if (nP13 == 0) nRes = 16;//P1.5输出低电平P1OUT = ~(BIT4);nP10 = P1IN BIT0;if (nP10 == 0) nRes = 9;nP11 = P1IN BIT1;if (nP11 == 0) nRes = 10;nP12 = P1IN BIT2;if (nP12 == 0) nRes = 11;nP13 = P1IN BIT3;if (nP13 == 0) nRes = 12;//P1.6输出低电平P1OUT = ~(BIT4);nP10 = P1IN BIT0;if (nP10 == 0) nRes = 5;nP11 = P1IN BIT1;if (nP11 == 0) nRes = 6;nP12 = P1IN BIT2;if (nP12 == 0) nRes = 7;nP13 = P1IN BIT3;if (nP13 == 0) nRes = 8;//P1.7输出低电平P1OUT = ~(BIT4);nP10 = P1IN BIT0;if (nP10 == 0) nRes = 1;nP11 = P1IN BIT1;if (nP11 == 0) nRes = 2;nP12 = P1IN BIT2;if (nP12 == 0) nRes = 3;nP13 = P1IN BIT3;if (nP13 == 0) nRes = 4; P1OUT = 0x00;//恢复以前值。 //读取各个管脚的状态nP10 = P1IN BIT0;nP11 = P1IN BIT1;nP12 = P1IN BIT2;nP13 = P1IN BIT3;for(;;){?? if(nP10 == 1 nP11 == 1 nP12 == 1 nP13 == 1)?? {??? //等待松开按键??? break;?? }}return nRes;}// 处理来自端口 1 的中断interrupt [PORT1_VECTOR] void PORT_ISR(void){Delay();KeyProcess();??? if(P1IFG BIT0)??? {??? ??? P1IFG = ~(BIT0);// 清除中断标志位??? }??? if(P1IFG BIT1)??? {??? P1IFG = ~(BIT1);// 清除中断标志位??? }??? if(P1IFG BIT