PCB常用英语汇总.docVIP

1板面凹痕 dent 2内层白斑 I/L white spot 3线路缺口 circuit nick 4蚀刻不净 undering etching 5绿油剥离 S/M peel off 6显影不净 under developing 7基 材 白 点 laminate measling 8铜面氧化 copper oxide 9绿油上焊盘 s/m on pad 10白字上焊盘 c/m on pad 11阻焊不良 poor S/M 12线路擦花 track scratch 13锡上线 sn on circuit 14聚锡 sn mass 15锡灰 sn gray 16焊盘露铜 cu exposed on pad 17锡上金手指 sn on G/F 18金手指凹痕 G/F dent 19金手指擦花 G/F scratch 20金手指粗糙 G/F roughness 21v-cut不良 poor V-cut 22倒边不良 poor milling 23针床压伤 ET dent 24拖锡不良 poor touch up 25补金不良 poor repairing Au 26补油不良 poor repairing s/m 27针孔 pinhole 28胶渍 paster stain 29k孔内毛刺 burrs in hole 30锡珠入孔 solder in hole 31露铜 expose Cu 32露镍 expose Ni 33绿油起泡 solder mask blister 34绿油起皱 solder mask winbles 35金手指氧化 G/F oxiding 36金颜色不良 Au discoloration 37金面凸起 Au surface blister 38绿油入孔 solder mask in hole 39爆板 board angle damafe 40翘板 warp 41漏印字符 skip 42金粗 Au too big 43金簿 Au too thin 44金手指缺口 G/F voids/nick on G/F 45金手指发黑 G/F too black 46字符印反 inverse C/M 47金手指针孔 G/F pinholes 48标志不清 symbol unclear 49标志错 symbol wrong 50绿油鬼影 ghost in S/M 51手指印 finger print 52补线不良 poor line repairing 53锡高 exessive solder 54孔小 hole undersize 55字符错 wrong C/M 56字符印偏 C/M misalignment 57字符入孔 C/M in hole 58字符 重影 C/M doubloe image 59漏镀金手指 missing plating G/F 60金手指发白 G/F gray 61焊盘脱落 pad break off/pad peel off 62焊盘露铜 pad expose cu 63断绿油桥 missing S/M bridge 64塞孔 block hole 65水迹 water print 66锡珠 solder ball 67砂孔 pitting 68油薄 　 69聚油 excess solder mask 70锡粗 Sn too thick 71线路上锡 Sn overlap scratch 72绿 油 下 杂 物 contamination under S/M 73焊盘损坏 land damage 74焊盘翘起 lifted land 75偏位 misregistration 76漏钻孔 missing hole 77焊盘缺口 nick on pad 78线路缺口 nick on track 1开路 open circuit 2短路 short circuit 线路狗牙 circuit wist 3线路缺口 circuit nick 4线路凹痕 circuit dent 5渗镀 plating Bloody 6焊盘缺口 pad nick 7内层白斑 I/L white spot 8黑化不良 poor B.O 9爆板 measling 10粉红圈 pinking ring 11层压起泡 press blister 12错位 misregistation 13偏位 shift 14孔内无铜 no Cu on Pth 15孔内毛刺 hole burrs 16NPTH有铜 Cu on NPTH 17铜面露基材 exposed laminate 18铜面凹痕 dent on Cu surface 19胶渍 gum residue 20夹膜 D/F nip 21蚀刻不尽 under etching 22