- 1、本文档共13页,可阅读全部内容。
- 2、原创力文档(book118)网站文档一经付费(服务费),不意味着购买了该文档的版权,仅供个人/单位学习、研究之用,不得用于商业用途,未经授权,严禁复制、发行、汇编、翻译或者网络传播等,侵权必究。
- 3、本站所有内容均由合作方或网友上传,本站不对文档的完整性、权威性及其观点立场正确性做任何保证或承诺!文档内容仅供研究参考,付费前请自行鉴别。如您付费,意味着您自己接受本站规则且自行承担风险,本站不退款、不进行额外附加服务;查看《如何避免下载的几个坑》。如果您已付费下载过本站文档,您可以点击 这里二次下载。
- 4、如文档侵犯商业秘密、侵犯著作权、侵犯人身权等,请点击“版权申诉”(推荐),也可以打举报电话:400-050-0827(电话支持时间:9:00-18:30)。
查看更多
毕 业 设 计(论文)
外 文 文 献 翻 译
文献、资料中文题目:轴承的摩擦与润滑
文献、资料英文题目:Friction , Lubrication of Bearing
文献、资料来源:
文献、资料发表(出版)日期:
院 (部):
专 业:
班 级:
姓 名:
学 号:
指导教师:
翻译日期: 2017.02.14
Friction , Lubrication of Bearing
In many of the problem thus far , the student has been asked to disregard or neglect friction . Actually , friction is present to some degree whenever two parts are in contact and move on each other. The term friction refers to the resistance of two or more parts to movement.
Friction is harmful or valuable depending upon where it occurs. friction is necessary for fastening devices such as screws and rivets which depend upon friction to hold the fastener and the parts together. Belt drivers, brakes, and tires are additional applications where friction is necessary.
The friction of moving parts in a machine is harmful because it reduces the mechanical advantage of the device. The heat produced by friction is lost energy because no work takes place. Also , greater power is required to overcome the increased friction. Heat is destructive in that it causes expansion. Expansion may cause a bearing or sliding surface to fit tighter. If a great enough pressure builds up because made from low temperature materials may melt.
There are three types of friction which must be overcome in moving parts: (1)starting, (2)sliding, and(3)rolling. Starting friction is the friction between two solids that tend to resist movement. When two parts are at a state of rest, the surface irregularities of both parts tend to interlock and form a wedging action. To produce motion in these parts, the wedge-shaped peaks and valleys of the stationary surfaces must be made to slide out and over each other. The rougher the two surfaces, the greater is starting friction resulting from their movement .
Since there is usually no fixed pattern between the peaks and valleys of two mating parts, the irregularities do not interlock once the parts are in
您可能关注的文档
- 51单片机简介Brief-introduction-of51MCU大学毕业论文外文文献翻译及原文.doc
- Commercial-Buildings商业楼宇大学毕业论文外文文献翻译及原文.doc
- Cooling-Towers冷却塔大学毕业论文外文文献翻译及原文.doc
- CUSTOMER-RELATIONSHIP-MANAGEMENT客户关系管理大学毕业论文外文文献翻译及原文.doc
- Database-Management-System数据库管理系统大学毕业论文外文文献翻译及原文.doc
- Financial-Risk-Management财务风险管理大学毕业论文外文文献翻译及原文.doc
- GeneralRequirementsToConstructionOfSubstation变电站建设的一般要求大学毕业论文外文文献翻译及原文.doc
- Intelligent-lighting-control-system智能照明控制系统大学毕业论文外文文献翻译及原文.doc
- Life-insurance人寿保险大学毕业论文外文文献翻译及原文.doc
- Mixer-works-and-optimize-the-design混合机工作原理及优化设计大学毕业论文外文文献翻译及原文.doc
文档评论(0)