中空圆柱ansys模态分析仿真命令流.doc

FINISH /CLEAR,START /COM,ANSYS RELEASE 10.0 U 14:17:19 03/22/2016 /input,start100,ans,d:\Program Files\Ansys Inc\v100\ANSYS\apdl\,,,,,,,,,,,,,,,,1 /COM,ANSYS RELEASE 10.0 U 21:40:25 03/20/2016 /input,start100,ans,d:\Program Files\Ansys Inc\v100\ANSYS\apdl\,,,,,,,,,,,,,,,,1 /DIST,1,1.08222638492,1 /REP,FAST /DIST,1,1.08222638492,1 /REP,FAST /DIST,1,1.08222638492,1 /REP,FAST /DIST,1,1.08222638492,1 /REP,FAST !* /NOPR /PMETH,OFF,0 KEYW,PR_SET,1 KEYW,PR_STRUC,1 KEYW,PR_THERM,0 KEYW,PR_FLUID,0 KEYW,PR_ELMAG,0 KEYW,MAGNOD,0 KEYW,MAGEDG,0 KEYW,MAGHFE,0 KEYW,MAGELC,0 KEYW,PR_MULTI,0 KEYW,PR_CFD,0 /GO !* /COM, /COM,Preferences for GUI filtering have been set to display: /COM, Structural !* /PREP7 !* ET,1,SOLID186 !* !* MPTEMP,,,,,,,, MPTEMP,1,0 MPDATA,EX,1,,2.1e11 MPDATA,PRXY,1,,0.3 MPTEMP,,,,,,,, MPTEMP,1,0 MPDATA,DENS,1,,7860 K,1,-0.025,0,0, K,2,0,0.025,0, K,3,0.025,0,0, K,4,0,-0.025,0, K,5,-0.02,0,0, K,6,0,0.02,0, K,7,0.02,0,0, K,8,0,-0.02,0, K,9,-0.025,0,0.224, K,10,0,0.025,0.224, K,11,0.025,0,0.224, K,12,0,-0.025,0.224, K,13,-0.02,0,0.224, K,14,0,0.02,0.224, K,15,0.02,0,0.224, K,16,0,-0.02,0.224, K,17,-0.025,0,0.776, K,18,0,0.025,0.776, K,19,0.025,0,0.776, K,20,0,-0.025,0.776, K,21,-0.02,0,0.776, K,22,0,0.02,0.776, K,23,0.02,0,0.776, K,24,0,-0.02,0.776, K,25,-0.025,0,1.1, K,26,0,0.025,1.1, K,27,0.025,0,1.1, K,28,0,-0.025,1.1, K,29,-0.02,0,1.1, K,30,0,0.02,1.1, K,31,0.02,0,1.1, K,32,0,-0.02,1.1, CSYS,2 L, 25, 26 L, 26, 27 L, 27, 28 L, 28, 25 L, 29, 30 L, 30, 31 L, 31, 32 L, 32, 29 L, 21, 22 L, 22, 23 L, 23, 24 L, 24, 21 L, 17, 18 L, 18, 19 L, 19, 20 L, 20, 17 L, 9, 10 L, 10, 11 L, 11, 12 L, 12,