微电子电路[第5版]8章节习题.pptVIP

8.1 课本744页8.1 Evaluation only. Created with Aspose.Slides for .NET 3.5 Client Profile 5.2.0.0. Copyright 2004-2011 Aspose Pty Ltd. 8.2 课本745页8.11 Evaluation only. Created with Aspose.Slides for .NET 3.5 Client Profile 5.2.0.0. Copyright 2004-2011 Aspose Pty Ltd. 8.3 试判别以下各图中放大器的反馈类型和反馈性质。图中，电容对信号均视作短路 并联-并联负反馈 并联-串联正反馈 反馈网络：Rf 反馈网络：Rf，RE2 if ii is if ii is Evaluation only. Created with Aspose.Slides for .NET 3.5 Client Profile 5.2.0.0. Copyright 2004-2011 Aspose Pty Ltd. 串联-串联正反馈 并联-串联负反馈 反馈网络：RE1、RE2 + Vf - + Vi - + Vs - 反馈网络：Rf、Cf、RE2 Evaluation only. Created with Aspose.Slides for .NET 3.5 Client Profile 5.2.0.0. Copyright 2004-2011 Aspose Pty Ltd. 串联-串联正反馈 Vo2:串联-并联负反馈 反馈网络：R、RE2 + Vf - + Vi - + Vs - 反馈网络：RE Vo1:串联-串联负反馈 + Vf - Evaluation only. Created with Aspose.Slides for .NET 3.5 Client Profile 5.2.0.0. Copyright 2004-2011 Aspose Pty Ltd. 串联-并联负反馈 反馈网络：R1、RG + Vf - Evaluation only. Created with Aspose.Slides for .NET 3.5 Client Profile 5.2.0.0. Copyright 2004-2011 Aspose Pty Ltd. 8.4 在下图所示电路中，按下列要求分别接成所需的两级反馈放大器电路 (1)具有稳定的源电压增益； （1）串联-并联 2-5、7-4 负反馈 + Vf - 端口1~7说明： 端口1和4为第一级差分对 的输入 端口6和7为第二级放大器 的输出 端口2和3为第一级差分对 的输出 端口5为第二级的输入 Evaluation only. Created with Aspose.Slides for .NET 3.5 Client Profile 5.2.0.0. Copyright 2004-2011 Aspose Pty Ltd. （2）具有低输入电阻和稳定的输出电流； （2）并联-串联 2-5、6-1 负反馈 Evaluation only. Created with Aspose.Slides for .NET 3.5 Client Profile 5.2.0.0. Copyright 2004-2011 Aspose Pty Ltd. （3）具有高输出电阻和输入电阻； （3）串联-串联 负反馈 3-5、6-4 + Vf - Evaluation only. Created with Aspose.Slides for .NET 3.5 Client Profile 5.2.0.0. Copyright 2004-2011 Aspose Pty Ltd. （4）具有稳定的输出电压和低的输入电阻。 （4）并联-并联 负反馈 3-5、7-1 Evaluation only. Created with Aspose.Slides for .NET 3.5 Client Profile 5.2.0.0. Copyright 2004-2011 Aspose Pty Ltd. 8.7 试判断下列图所示电路的反馈类型，并在满足深度负反馈条件下，求电压增益和源电压增益。电容对交流旁路。 Evaluation only. Created with Aspose.Slides for .NET 3.5 Client Profile 5.2.0.0. Copyright 2004-2011 Aspose Pty Ltd. 8.8 试判断下列图所示电路的反馈类型，并在满足深