29种机械安全技术操作程29种机械安全技术操作规程.docVIP

目? 录 一、土石方机械 1、装载机安全技术操作规程·······························1 二、动力机械 1、发电机安全技术操作规程································2 2、锅炉安全技术操作规程·································3 三、起重机械· 1、起重安全操作规程·····································4 2、塔式起重机安全技术操作规程···························5 3、汽车起重机安全技术操作规程···························6 4、龙门起重机安全技术操作规程···························7 5、叉车安全技术操作规程·································8 6、卷扬机安全技术操作规程······························9 四、运输机械 1、轨道车安全技术操作规程······························10 2、牵引车安全操作规程··································11 五、砼及砂浆机械 1、混凝土搅拌机安全技术操作规程·························12 2、混凝土搅拌站安全技术操作规程························13 3、砂浆搅拌机安全技术操作规程··························14 4、张拉安全操作规程···································15 六、焊接机械 1、电焊机安全技术操作规程······························16 2、气焊安全技术操作规程································17 3、对焊机安全技术操作规程······························18 七、加工机械 1、车床安全技术操作规程·······························19 2、刨床安全技术操作规程·······························20 3、钻床安全技术操作规程·······························21 4、空气锤安全技术操作规程······························22 5、钢筋切断机安全技术操作规程··························23 6、钢筋弯曲机安全技术操作规程····??·····················24 八、其他 1、支拆模安全操作规程·································25 2、配电室安全技术操作规程······························26 3、现场施工用电安全技术操作规程·························27 4、手持电动工具安全技术操作规程·························29 5、电动砂轮机安全技术操作规程···························30 装载机安全技术操作规程 （1）装载机行驶时，应收回铲斗，铲斗离地约400～500mm。在行驶过程中注意是否有路障或高压线等。除规定的驾驶人员外，不准搭乘其它人员。 （2）装载机行驶时，避免突然换向行驶，铲斗带负荷升起行驶时，不准急转弯和急刹车。 （3）装载机在公路上行驶时必须遵守交通规则，谨慎驾驶，下坡禁止空档溜放。 （4）在倾斜坡地若发动机熄火，应把铲斗放在地上并制动，将各操作杆置于中位，再启动发动机。 （5）装载机应注意斗杆不应升太高。 （6）对边坡、壕沟、凹坑卸料时，注意不要使铲斗过于伸出，以免倾覆。 （7）不得在倾斜度超过规定的场地上工作，作业区内不得有障碍物及无关人员。 （8）装载机转向架未锁闭时，严禁站在前后车架之间检修保养。 （9）大臂升起后，在进行润滑和调整等工作前，必须装好安全销或采取其它措施支住大臂，以防大臂落下伤人。 （10）作业后，应将装载机停放在安全场地，将铲斗平放地面，所有操作杆置于中位，并制动锁定。 ? 发电机安全技术操作规程 （1）启动前应检查燃油箱油量是否充足，各油管及接头处无漏油现象；冷却系统水量是否充足、清洁、无渗漏，风扇皮带松紧是否合适。检查内燃机与发电机传动部分应连接可靠，输出线路的导线绝缘良好，各仪表齐全、有效。 （2）启动后，应低速运转3～5分钟，待温度和机油压轮均正常后，方可开始作业。发电机在升速中应无异响，滑环及整流子上电刷接触良好，无跳动及冒火花现象。待运