带式输送机原始设计论文（论文）.docVIP

中国矿业大学成人教育学院2009届毕业设计（论文） PAGE   PAGE 49  PAGE \* MERGEFORMAT 1 (此文档为word格式，下载后您可任意编辑修改！) 摘 要 随着带式输送机在煤矿、码头、电厂等地方的使用越来越广泛，对运输能力大，倾角大的皮带机需求也越来越多，更要求它们安全可靠，自动化程度高，经营费用低，从而节约基建投资。 本文针对大倾角、高强度带式输送机设计过程中存在的问题，从四个方面对大倾角带式输送机进行分析研究。 从理论上解析大倾角带式输送机的计算过程，从大倾角带式输送机的理论入手，详细计算物料的横截面积、圆周力、滚筒轴功率和电机功率，利用逐点计算法计算各个滚筒的合张力以及传动滚筒的扭距，计算出胶带的最大张力和最大逆止力矩，给大倾角皮带机在煤矿井下的使用给予理论上的支持。 对部件的结构提出具体的设计思路，从驱动装置入手，引进了机电液一体化的可控制软启动传输，它既能实现皮带机软启动，又能很好的保证电动机的功率平衡，在皮带机的中间部分的承载段，设置了有4个托辊的深槽型托辊组，对提高物料对胶带的摩擦力，提高运输倾角有很大的作用。在逆止器的设计过程中，采用了低速轴逆止器，要求能独立完成逆止性能，提高了皮带机的安全性，以保证大倾角皮带机的安全运行。 关键词：大倾角；高强度；带式输送机；结构设计 ABSTRACT With the more and more application of belt conveyor in coal mine,wharf, power station and other places, the needs for belt conveyor with super-long distance , order to save the investment of fundamental construction. This paper research on the problems in the designing process of the belt conveyor with super-long disrance, of every drum and torsion of driving drum, calculating the maximum strain and the maximum reverse stopping torque, to give the support on theory for using belt conveyor with super-long distance, achieve flexible start-up of belt conveyor, but also can better guarantee the balance of motor power.There is a deep groove rollers with 4 carrier roller in the middle loading line of belt conveyor, this play an important role in enhancing the friction that the material give to the belt and advancing carriage dip. In the designing process of backstops, there are 2 backstops which required to complete the principle of the backstop independently are employed, in this case the capacity of security is advanced, in order to insure the belt conveyor with 目 录 绪论……………………………………………………………………1 1.1目前皮带机的应用情况………………………………………… 1 1.2大倾角线路物料输送的类型及特点…………………………… 1 输送机初步设计计算………………………………………………… 6 2.1 带式输送机原始参数…………………………………………… 6 2.2 初步设计计算…………………………………………………… 6 输送机的动力学特性研究……………………………………………24 3.1 大倾角带式输送机起动性能计算分析………………