化学螺栓规格汇.docVIP

图 1 化学锚栓系列技术数据配合钢筋使用一种植钢筋种植钢筋的承载力与基本材料强度直接相关。下表为施工参数，给出基体混凝土强度C30、II级钢筋的载荷特征值。钢筋直径Фmm钻孔直径Фmm结合力特征值钢筋屈服理论埋深mmRk（NK）10142526.3105121634.538.0135141843.548.551.5175162052.557.563.567.551.5210182263.569.576.582.585.5255202583.590.594.599.5105.5295222892.599.5106.5114.5127.53552532106.5115.0125.0138.5156.04252837125.0142.0158.0178.5192.55153240157.5180.0200.0218.0235.0252.0625埋植深度mm100120140160180200220240260280300350400450500550600施工步骤：钻孔：用冲击电站钻按照规定的孔径和孔深钻孔，参见技术数据； 清孔：刷除、吹净钻屑，交替操作三遍； 注胶：使用配套挤压器从钻孔底部开始向外挤入胶剂，空心基材注胶前需置入筛网，每支药剂量初挤出的未充分混合部分不能使用，直至充分混合。每次更换药剂时，必须同时更换新的混合管； 植入：旋入钢筋或螺杆，并调整到规定位置，须在规定操作时间内完成； 固化：在凝胶固化过程中，切忌触碰钢筋或螺杆； 加载：待充分固化后，加载紧固。操作时间和固化时间基本温度（℃）40302050-5操作时间（分钟）246202535固化时间（分钟）253045100180360锚固力设计值（KN）规格埋深（mm）拔力30°合力45°合力60°合力剪力C20C25≥C30C20C25≥C30C20C25≥C30C20C25≥C30≥C20M109012.212.212.28.58.58.57.57.57.56.56.56.56.0M1211017.817.817.812.012.012.010.510.510.59.59.59.58.5M1611520.022.033.014.516.023.013.014.520.512.013.018.016.5M2017031.034.052.023.025.036.020.522.531.519.021.028.026.5M2422045.049.075.022.036.052.029.532.545.027.030.041.037.0M3028073.080.0120.053.059.083.047.552.073.044.048.065.060.0锚固力极限标准值（KN）规格埋深（mm）拔力30°合力45°合力60°合力剪力C20C25≥C30C20C25≥C30C20C25≥C30C20C25≥C30≥C20M109028.028.028.019.519.519.516.816.816.815.315.315.313.8M1211044.544.544.527.817.827.824.524.524.522.122.122.120.0M1611560.566.576.044.549.553.239.843.845.924.540.041.838.1M2017094.5104.0118.070.576.882.062.568.071.545.963.065.059.0M24220135.0150.0170.0100.5110.4118.089.59