钢管规格资料.docVIP

PN1.0压力电力钢制管道规格表 一：钢管、法兰与弯头 序号规格钢管法兰弯头（标准GB/T12459-1990）备注规格单重外径螺栓孔中心孔尺寸螺栓孔直径螺栓孔数量法兰厚度法兰内径（B）单重90°45°尺寸单重尺寸单重1DN25φ32×2.51.1891158514416331.12L1=L2=88,δ=2.50.251L1=L2=500.14350°以下为45°计算,50°以上为90°计算。2DN32φ38×2.52.19814010018418391.86L1=L2=98,δ=2.50.337L1=L2=550.2023DN40φ45×2.52.6215011018418462.12L1=L2=107,δ=2.50.44L1=L2=600.2644DN50φ57×3416512518420592.77L1=L2=126,δ=30.79L1=L2=650.408φ57×3.54.625DN65φ76×3.56.2618514518420783.31L1=L2=145,δ=3.51.424L1=L2=760.746φ76×47.16DN80φ89×48.3820016018820913.59L1=L2=164,δ=42.158L1=L2=801.0537DN100φ108×410.26220180188221104.57L1=L2=202,δ=43.252L1=L2=1051.698DN125φ133×412.72250210188221355.65L1=L2=250,δ=44.99L1=L2=1142.289DN150φ159×4.517.14285240228241617.61L1=L2=289,δ=4.57.78L1=L2=1303.510DN200φ219×631.52340295228242229.24L1=L2=375,δ=618.55L1=L2=1887.6711DN250φ273×639.4839535022122627611.9L1=L2=451,δ=732.5L1=L2=22311.61φ273×745.8912DN300φ325×647.1744540022122832814.6L1=L2=537,δ=852.7L1=L2=21521.89φ325×862.5413DN350φ377×872.7650546022163038118.9L1=L2=61,δ=870.3L1=L2=29129.1314DN400φ426×10102.556551526163243024.4L1=L2=700,δ=890.59L1=L2=32237.6615DN450φ478×10115.361556526203548527.9L1=L2=776,δ=8112.9L1=L2=32248.85 二：大小头 规格厚度及长度单重规格厚度及长度单重规格厚度及长度单重DN32/25δ=3, L=1510.357DN40/32δ=3, L=1640.467DN40/25δ=3, L=1640.43DN50/40δ=4, L=1760.824DN50/32δ=4, L=1760.755DN50/25δ=3, L=1510.703DN65/50δ=4, L=1891.165DN65/40δ=4, L=1891.062DN65/32δ=4, L=1890.988DN80/65δ=4, L=1891.463DN80/50δ=4, L=1891.296DN80/40δ=4, L=1891.174DN100/80δ=4, L=2021.88DN100/65δ=4, L=2021.753DN100/50δ=4, L=2021.56DN125/100δ=4, L=2472.84DN125/80δ=4, L=2472.6