办公楼门扇的安装操作方法.docVIP

办公楼门扇的安装操作方法 办公楼门扇的安装操作方法提要：修刨时，在门扇的高度方向先刨平下冒头，以此为准再修刨上冒头；在宽度方向上应将门扇立于门窗框中，检查与门框配合的松紧度 更多精品源自制度 办公楼门扇的安装操作方法 ①工艺流程图: ②主要操作要点: ⑴门扇安装前，应检查门框上、中、下三部分的宽度是否一致，如果偏差2mm以上要进行修整。要明确开启方向，而后量出门框口的净尺寸，考虑风缝的大小，再确定扇的高度和宽度，即进行修刨。 ⑵修刨时，在门扇的高度方向先刨平下冒头，以此为准再修刨上冒头；在宽度方向上应将门扇立于门窗框中，检查与门框配合的松紧度，根据留缝要求进行修刨。由于木材的干缩湿胀，而且门扇、框均需要油漆涂饰及打底厚度，所以安装时要留缝，包括上述的风缝。门扇与地面缝、门扇与门企缝。 ⑶门扇安装，采用初安→调整→临时固定→安装固定的流程进行。修刨好的门窗扇，用木楔临时立于门窗框中，安排好缝隙后面的合页位置。合页位置距上、下边的距离宜为门扇高度的1/10，此位置利于合页受力，又可避开榫头。然后再把扇取下，用扁铲剔出合页槽。合页槽应外边浅，里边深，其深度应是把合页合上以后能够与框、扇平正为准。剔槽后放入合页，上下合页各拧1颗螺丝钉将扇挂上，检查缝隙是否符合要求，扇与框是否齐平，扇能否关好。在检查合格后，再将螺丝钉全部上齐。对于双扇门扇的安装，还需注意其错口工序，按其开启方向看，右手门是盖口，左手门是等口。 ⑷比准锁头、锁母位置后，先安装锁母，再安装锁头，并进行各种用途的调试。 ⑸进行门扇安装的综合检查，确认合格后即可进行下道工序施工。 ⑹验收标准参见《建筑装饰装修工程质量验收规范》。 Measures for the routine management of moral education in Middle SchoolsMethod of conventional management of moral education in middle schoolFirst, the guiding ideology:School moral education is an organic whole of the whole education work, always adhere to the school adhere to the moral education, education for this product, and actively promote the quality education, the school building efficient curriculum system of moral education, moral education, improve the sense of attraction and appeal, enhance the moral education work for through and timeliness. Teach everyone, service education and management education, and school moral education work must be with family education and community education closely together, to form a concerted pattern, and strive to create a good atmosphere for education, and to promote the all-round development of students, to establish a scientific moral education full of vigor the For long-term mechanism.Two, the goal of moral education:To guide the students to form the correct world outlook, outlook on life, values, to cultivate students unity and mutual assistance, honest and trustworthy, law-abiding, good quality, hard work, set a good XX students ideological quality, psychological quality and image qualit