地下人防工程圈梁施工方法.docVIP

地下人防工程圈梁施工方法 地下人防工程圈梁施工方法提要：钢筋绑扎前要检查，不得有油渍、漆污、铁锈等。各接点绑扎及预埋件埋设和焊接一定要按图施工，各绑扎、焊接头、保护层应符合设计及规范要求 更多建筑学堂 地下人防工程圈梁施工方法 1施工工艺流程 测量定位→素砼垫层找平→钢筋绑扎→立模→砼浇注→拆模及养护 2施工方法 测量放线 准确测放中心位置，进行支撑节点的定位，按设计要求弹线，确定圈梁边线和轴线。 钢筋加工及立模 钢筋绑扎前要检查，不得有油渍、漆污、铁锈等。各接点绑扎及预埋件埋设和焊接一定要按图施工，各绑扎、焊接头、保护层应符合设计及规范要求。绑扎好后不得踩踏，经监理验收合格后，进行支模工序，在浇筑混凝土前还应进行钢筋复检。 清理干净绑扎钢筋时留下的污泥、槽内杂物。检查模板并在其内侧涮上脱模剂，钢模要平整、牢固，不应有通缝。要求双侧模除有支撑加固外，还应每隔2-3m有一道φ8钢筋拉固两侧模板。模板经监理验收后才进入下道工序。 混凝土浇灌、振捣及养护。 混凝土应振捣密实，表面平整，不得出现蜂窝、麻面和露筋现象。 在施工过程中尽量少留施工缝，重新浇灌砼时，应将该施工缝凿出并清洗干净，在界面用高标号砂浆湿润后继续砼浇灌。 按规定实施混凝土抽样制作试块。 混凝土圈梁需养护到设计强度时方可进行土方开挖。 重点工序质量控制措施 人工挖槽时，应一次挖成，不得用回填土找平。 钢筋绑扎时，要牢固、方正，电渣压力焊严格按设计图纸要求；钢筋规格、数量、位置、间距应准确无误，焊接时焊缝要连续、饱满、无夹渣、气泡。 支模板要牢固、平直，拼缝严实，不得有漏浆、变形等现象。 浇注砼时，要振捣充分，砼表面要压实抹平，不得有蜂窝、麻面。 Measures for the routine management of moral education in Middle SchoolsMethod of conventional management of moral education in middle schoolFirst, the guiding ideology:School moral education is an organic whole of the whole education work, always adhere to the school adhere to the moral education, education for this product, and actively promote the quality education, the school building efficient curriculum system of moral education, moral education, improve the sense of attraction and appeal, enhance the moral education work for through and timeliness. Teach everyone, service education and management education, and school moral education work must be with family education and community education closely together, to form a concerted pattern, and strive to create a good atmosphere for education, and to promote the all-round development of students, to establish a scientific moral education full of vigor the For long-term mechanism.Two, the goal of moral education:To guide the students to form the correct world outlook, outlook on life, values, to cultivate students unity and mutual assistance, honest and trustworthy, law-abiding, good quality, hard work, set a good XX students ideolog