安全生产责任制：电焊工安全生产职责.docVIP

安全生产责任制：电焊工安全生产职责 安全生产责任制：电焊工安全生产职责提要：电焊机外壳必须按地良好，其电源的装拆应由电工进行，电焊机要设单独的开关，开关应设在防雨的闸箱内，拉合时应戴手套侧向操作 安全生产责任制：电焊工安全生产职责 一、目的和适用范围 1、目的 为明确本岗位的安全职责，特制订本规定。 2、适用范围 本责任适用于本公司电焊工安全生产职责。 二、职责 1、电焊机外壳必须按地良好，其电源的装拆应由电工进行，电焊机要设单独的开关，开关应设在防雨的闸箱内，拉合时应戴手套侧向操作。 2、焊钳与反线必须绝缘良好，连接牢固，更换焊条应戴手套，在潮湿地点工作应站在绝缘胶板或木板上，严禁在带压力的容器或管道上施焊，焊接带电的设备必须先切断电源。 3、焊接贮存过易燃、易暴、有毒物品的容器或管道必须清除干净，并将所有孔口打开，在密闭金属容器内施焊时，容器必须可靠接地，通风良好，并应有人监护，严禁向容器内输入氧气，焊接预热工作时，应有石棉布或挡板等热措施。 4、不得用钢丝绳或机电设备代替零线，所有地线接头，必须连接牢固，更换场地移动把线时，应切断电源，并不得手持把线爬梯登高。 5、清除焊渣，采用电弧气刨清根时，应戴防护眼睛或面罩，防止铁渣飞溅伤人。多台焊机在一起集中施焊时，焊接平台或焊件接地，并应有隔光板，施焊场地周围应清除易燃、易爆物品或进行覆盖隔离 6、雷雨时应停止露天焊接作业，必须在易燃、易爆或液体扩散区施焊时，应经有关部门检查许可后方可施焊，工作结束应切断电源，并检查操作地点，确认无复燃后方可离开。 Measures for the routine management of moral education in Middle SchoolsMethod of conventional management of moral education in middle schoolFirst, the guiding ideology:School moral education is an organic whole of the whole education work, always adhere to the school adhere to the moral education, education for this product, and actively promote the quality education, the school building efficient curriculum system of moral education, moral education, improve the sense of attraction and appeal, enhance the moral education work for through and timeliness. Teach everyone, service education and management education, and school moral education work must be with family education and community education closely together, to form a concerted pattern, and strive to create a good atmosphere for education, and to promote the all-round development of students, to establish a scientific moral education full of vigor the For long-term mechanism.Two, the goal of moral education:To guide the students to form the correct world outlook, outlook on life, values, to cultivate students unity and mutual assistance, honest and trustworthy, law-abiding, good quality, hard work, set a good XX students ideological quality, psychological quality and image quality. The formation of excell