无齿切割机切割作业安全技术交底.docVIP

无齿切割机切割作业安全技术交底 无齿切割机切割作业安全技术交底提要：随时清理铁屑、杂物保持工作点整洁，做到活完场清脚下净，切割点应远离易燃物和行走人员较多的地点 无齿切割机切割作业安全技术交底 工程名称交底日期：年月日 　　施工单位分项工程名称：无齿切割机切割作业 　　交底提要 　　交底内容： 1.切割机应购置证件齐全的合格产品； 2.操作人员应熟知安全操作技术规程，作业前进行安全教育和指导性操作； 3.进入现场戴好合格的安全帽，系好下颚带，锁好带扣，戴好护目镜及绝缘手套； 4.遵守施工现场的劳动纪律，着装应规范，不得光背穿拖鞋； 5.施工现场禁止追逐打闹和酒后作业； 6.班前检查切割机的外观是否完好，皮带轮防护罩和切割片的防护罩是否齐全； 7.切割机手柄开关灵敏有效，不得装设倒顺开关，控制开关一闸一机，一箱一漏开，专人操作控制； 8.切割机严禁雨、雪天气露天作业，严防触电事故的发生； 9.切割机切屑前方设挡护板，防止切屑灼烫伤人或发生火灾； 9.切割片应购买检验合格的外径边缘残损或切剩余直径小于250mm应更换； 10.随时清理铁屑、杂物保持工作点整洁，做到活完场清脚下净，切割点应远离易燃物和行走人员较多的地点； 11.切割机严禁做打磨机使用； 12.工作完毕后拉闸断电，配电箱上锁，室外服务业的切割机工作完毕应采取防雨、雪措施； 13.长期不用的切割机使用前，应首先看外观是否完好无损，开关是否灵活，电机绝缘值是否在允许启动范围之内，低于启动要求不允许使用； 14.切割作业过程中必须带好防尘口罩和护目镜。 审核人交底人接受交底人 1、本表头由交底人填写,交底人与接受交底人各保存一份，安全员一份； 2、当做分部、分项施工作业安全交底时,应填写”分部、分项工程名称”栏； 3、交底提要应根据交底内容把交底重要内容写上。 Measures for the routine management of moral education in Middle SchoolsMethod of conventional management of moral education in middle schoolFirst, the guiding ideology:School moral education is an organic whole of the whole education work, always adhere to the school adhere to the moral education, education for this product, and actively promote the quality education, the school building efficient curriculum system of moral education, moral education, improve the sense of attraction and appeal, enhance the moral education work for through and timeliness. Teach everyone, service education and management education, and school moral education work must be with family education and community education closely together, to form a concerted pattern, and strive to create a good atmosphere for education, and to promote the all-round development of students, to establish a scientific moral education full of vigor the For long-term mechanism.Two, the goal of moral education:To guide the students to form the correct world outlook, outlook on life, values, to cultivate students unity and mutual assistance, honest and tr