木龙骨吊顶施工工艺及技术要点.doc

木龙骨吊顶施工工艺及技术要点 木龙骨吊顶施工工艺及技术要点提要：龙骨应采用五扭曲的白松木。规格为40mm*30mm;吊杆宜用6mm通丝制作，或用40mm*30mm白松龙骨做吊杆，木龙骨要刷防火涂料二度，与墙顶接触面要刷防腐涂料 木龙骨吊顶施工工艺及技术要点 施工工艺 弹线-——打吊筋-——固定边龙骨——固定通长（主）龙骨——固定横称龙骨——调整——覆面板 具体做法： 沿墙弹出天棚的标高线，及顶面吊筋、（吊杆）线的位置。木龙骨刷防火涂料两道。 吊筋（杆）、沿边龙骨位置打眼。顶部打眼时电锤上要加装等灰罩，以免溅到眼睛。 打上木塞，并固定沿边龙骨及吊杆木基（或通丝吊筋），吊杆木基钉距不大于800-----1000mm。 4.固定通长（主）龙骨，对于跨度较大的先把通长龙骨 5.此龙骨（横称）位置弹线、固定。 6.用麻线在横、竖中心位置带线，以线校整顶棚龙骨的平整度，并用吊筋固定好。吊筋（杆）与主龙骨的固定螺丝（钉）应拧在主龙骨的侧面，木吊杆与吊杆木基（钉于楼板的木料）的连接，应放在侧面，用钉固定。 7.天棚龙骨调整好后，待隐蔽工程验收通过覆面板。覆面板时先覆大板后找补小块，板缝要错开固定。 技术要求 1.龙骨应采用五扭曲的白松木。规格为40mm*30mm;吊杆宜用6mm通丝制作，或用40mm*30mm白松龙骨做吊杆，木龙骨要刷防火涂料二度，与墙顶接触面要刷防腐涂料。 2.吊顶造型要符合设计要求。 3.吊顶连接要牢固，端头不能开裂，间距为600------1000mm。吊顶中间应起拱，高度为短向跨度的1/200，横竖向起拱要均匀。龙骨间距不大于400mm。 4.纸面石膏板要在自由状态下固定，长边应沿次龙骨方向铺装。自攻螺丝距包缝边10——15mm,距切割边15——17mm,钉距150——170mm,石膏板接缝要留3——5mm,螺丝与板面垂直用螺丝刀拧入，不得用钉锤打入，略埋与板面，钉眼要点红丹防锈漆两度，并用胶水调石膏腻子铺平钉眼。 5.周围应在同以水平面，其高度不得大于5mm,接缝平直度偏差不大于2mm，接缝高低差应小于。 Measures for the routine management of moral education in Middle SchoolsMethod of conventional management of moral education in middle schoolFirst, the guiding ideology:School moral education is an organic whole of the whole education work, always adhere to the school adhere to the moral education, education for this product, and actively promote the quality education, the school building efficient curriculum system of moral education, moral education, improve the sense of attraction and appeal, enhance the moral education work for through and timeliness. Teach everyone, service education and management education, and school moral education work must be with family education and community education closely together, to form a concerted pattern, and strive to create a good atmosphere for education, and to promote the all-round development of students, to establish a scientific moral education full of vigor the For long-term mechanism.Two, the goal of moral education:To guide the students to form the correct world outlook, outlook on life,