模板安装质量验收标准.doc

模板安装质量验收标准 模板安装质量验收标准提要：模板板缝拼接严密、平整、无错台，模板拼缝部位设置的海绵条等防漏浆措施不得影响结构观感质量 模板安装质量验收标准 1、现浇结构模板安装允许偏差 项次项目允许偏差（mm）检查方法 1轴线位移柱、墙、梁3尺 量 2底模上表面标高±3水准仪或拉线检查 3截面模内尺寸基础±5尺 量 柱、墙、梁±3 4层高垂直度层高不大于5m3经纬仪或吊线、尺量 大于5m5 5相邻两板表面高低差2尺 量 6表面平整度2靠尺、塞尺 7阴阳角方正2方尺、塞尺 顺直2线 尺 尺寸+5、-0 胶合板的质量要求 胶合板的翘曲度≤1% 胶合板的尺寸公差长度公差±3mm 厚度公差12± 对角线之差≤5mm 拼缝缝隙最宽处≤ 板边缺损≤10mm 胶合板模板加工的质量要求 检查内容允许误差（mm） 长 度2 宽 度2 对角线4 边缘平直2 边缘毛刺无 2、模板安装观感质量 模板板面平整、光滑，尺寸准确，尺寸偏差不大于2mm，背楞焊接牢固，刚度足够。 模板背楞在支架部位预留园孔，要求无扭曲、破损、毛刺，位置准确，操作平台、支架安装牢固。 模板板缝拼接严密、平整、无错台，模板拼缝部位设置的海绵条等防漏浆措施不得影响结构观感质量。 胶合板表面不得有水泥浮浆，表面的杂物应擦洗干净。顶板模板板缝采用硬拼的方式，不得采用粘贴胶带的方法。因周转使用的结果，板缝部位如有毛刺应及时弹线切去，以保证板缝效果。 模板内外清理干净，脱模剂的涂刷应均匀、无漏刷、对工作面上的钢筋无污染，清理干净的模板材料应标识明确、堆放整齐。 支撑体系要安装牢固，无松动现象，板缝拼缝紧密，不变形不漏浆。 螺栓及”U”型卡、”3”型卡均应按设计要求安装到位，各板缝海绵条不得遗漏，不得嵌入柱内部。 Measures for the routine management of moral education in Middle SchoolsMethod of conventional management of moral education in middle schoolFirst, the guiding ideology:School moral education is an organic whole of the whole education work, always adhere to the school adhere to the moral education, education for this product, and actively promote the quality education, the school building efficient curriculum system of moral education, moral education, improve the sense of attraction and appeal, enhance the moral education work for through and timeliness. Teach everyone, service education and management education, and school moral education work must be with family education and community education closely together, to form a concerted pattern, and strive to create a good atmosphere for education, and to promote the all-round development of students, to establish a scientific moral education full of vigor the For long-term mechanism.Two, the goal of moral education:To guide the students to form the correct world outlook, outlook on life, values, to cultivate students unity and mutual assistance,