管道工程质量薄弱环节的预防措施.docVIP

管道工程质量薄弱环节的预防措施 管道工程质量薄弱环节的预防措施提要：管道支架固定不牢支架横梁要牢固地固定在墙、柱子或其它结构物上，横梁长度方向须水平，顶面与管子中心线平行 自建筑施工资料 管道工程质量薄弱环节的预防措施 1管道螺纹接口返潮、渗漏 螺纹采用套丝机严格按标准进行加工。要求螺纹端正、光滑、无毛刺、不断丝、不乱扣等。管螺纹的主要尺寸须符合安装规定。 管螺纹加工后，先用手拧入2-3扣，再用管钳拧紧，最后螺纹留出距连接件处2-3扣。在进行管螺纹安装时，选用合适的管钳，紧配件时，还需考虑配件的位置和方向，不允许因拧过头而用倒扣的方法进行找正。 管道安装完毕，严格按照施工验收规范的要求进行严密性试验和强度试验，认真检查管道和接头有无裂纹、砂眼等缺陷，丝头是否完好。 管道支吊架的距离须符合设计及规范规定，安装牢固。 2管道支架固定不牢 支架横梁要牢固地固定在墙、柱子或其它结构物上，横梁长度方向须水平，顶面与管子中心线平行，不允许上翘下垂或扭斜。 无热位移的管道吊架的吊杆要垂直于管道，吊杆的长度能调节。有热位移的管道，吊杆在位移相反方向，按位移值的二分之一倾斜安装。 固定支架能使管子平稳地放在支架上，不能有悬空现象。管卡须紧卡在管道上。由于固定支架承受着管道内介质压力的反力及补偿器的反力，因此固定支架的位置必须严格安装在设计规定的位置上。 活动支架不得妨碍管道由于热膨胀所引起的移动。其安装位置要从支承面中心向位移的反向偏移，偏移为位移的一半。同时管道的保温层不得妨碍热位移。 3漆层厚度不匀、附着不牢 涂刷底漆前，必须清除表面的灰尘、污垢、锈斑、焊渣等杂物；涂刷油漆，厚度均匀，色泽一致，无流淌及污染现象。 自建筑施工资料 Measures for the routine management of moral education in Middle SchoolsMethod of conventional management of moral education in middle schoolFirst, the guiding ideology:School moral education is an organic whole of the whole education work, always adhere to the school adhere to the moral education, education for this product, and actively promote the quality education, the school building efficient curriculum system of moral education, moral education, improve the sense of attraction and appeal, enhance the moral education work for through and timeliness. Teach everyone, service education and management education, and school moral education work must be with family education and community education closely together, to form a concerted pattern, and strive to create a good atmosphere for education, and to promote the all-round development of students, to establish a scientific moral education full of vigor the For long-term mechanism.Two, the goal of moral education:To guide the students to form the correct world outlook, outlook on life, values, to cultivate students unity and mutual assistance, honest and trustworthy, law-abiding, good quality, hard work, set a good XX students ideological quality, psyc