绑剪力墙钢筋施工工艺.docVIP

绑剪力墙钢筋施工工艺 绑剪力墙钢筋施工工艺提要：立2～4根竖筋：将竖筋与下层伸出的搭接筋绑扎，在竖筋上画好水平筋分档标志，在下部及齐胸处绑两根横筋定位，并在横筋上画好竖筋分档标志 精品源自保洁 绑剪力墙钢筋施工工艺 （1）工艺流程：立2～4根竖筋→画水平障距→绑定位横筋→绑其余横筋→绑其余横竖筋 （2）墙筋分布筋构造要求 1）转角墙阳角部位水平筋应连续转角设置，搭接区域不得在暗柱范围内，相邻（上下、内外）接头端部错开距离大于等于500mm； 2）墙水平筋在支座处如不能直锚，则需做15d弯钩，伸至对面筋内侧； 3）墙水平筋锚固在约束端（框、暗柱等）纵筋内侧； 4）水平分布筋在竖向分布筋的内侧还是外侧，依设计； 5）如剪力墙顶部有暗梁，且暗梁高≥，则弯锚长度为12d，伸至梁上部筋面上；如无暗梁，则按图集03G101-1，P48； 6）如剪力墙顶（中）部有框架梁，其纵向分布筋则需锚入框架梁内，如梁高≥，则弯锚长度为12d，伸至梁上部筋内侧；框架梁（暗梁）范围内剪力墙水平分布筋不应遗漏。 7）连梁梁侧纵向钢筋设计无要求时，则同相邻剪力墙水平分布筋。 （3）绑扎工艺 1）立2～4根竖筋：将竖筋与下层伸出的搭接筋绑扎，在竖筋上画好水平筋分档标志，在下部及齐胸处绑两根横筋定位，并在横筋上画好竖筋分档标志，接着绑其余竖筋，最后再绑其余横筋。 2）竖筋与伸出搭接筋的搭接处需绑3根水平筋，其搭接长度及位置均应符合设计要求，设计无要求时，按表1、表2施工。 3）剪力墙筋应逐点绑扎，双排钢筋之间应绑拉筋（拉筋构造见柱相关内容）或支撑筋，其纵横间距不大于600mm（设计有要求时，按设计），钢筋外皮用塑料卡。 4）剪力墙洞口周围加固筋（梁）等，应符合设计和规范相关要求。（图集03G101-1，P53） 5）合模后对伸出的竖向钢筋应进行修整，宜在搭接处绑一道横筋定位，浇筑混凝土时应有专人看管，浇筑后再次调整以保证钢筋位置的准确。 精品源自保洁 Measures for the routine management of moral education in Middle SchoolsMethod of conventional management of moral education in middle schoolFirst, the guiding ideology:School moral education is an organic whole of the whole education work, always adhere to the school adhere to the moral education, education for this product, and actively promote the quality education, the school building efficient curriculum system of moral education, moral education, improve the sense of attraction and appeal, enhance the moral education work for through and timeliness. Teach everyone, service education and management education, and school moral education work must be with family education and community education closely together, to form a concerted pattern, and strive to create a good atmosphere for education, and to promote the all-round development of students, to establish a scientific moral education full of vigor the For long-term mechanism.Two, the goal of moral education:To guide the students to form the correct world outlook, outlook on life, values, to cultivate students unity and mutual assistanc