花岗岩的翻新.docVIP

花岗岩的翻新 花岗岩的翻新作者：佚名 时间：2017-8-25 浏览量： 花岗岩俗称麻石,主要由石英、云母构成,摩氏硬度值为左右,质地坚硬,长期使用易出现自然风化和磨损现象,其表现特征为云母脱落。此时石材表面有小量凹入的麻点出现,当麻点不断增多时,花岗岩表面光亮度下降,失去原有光泽,用手触摸时有凹凸感,使用翻新可还原石材光泽。 由于花岗岩质地坚硬,故其表面受损时单纯使用化学类养护剂、研磨剂等进行养护很难达到理想效果,因此运用大型的石材翻新机采用物理研磨方法,其效果要好于单纯使用化学类产品进行翻新研磨。使用物理研磨方法必须满足两个条件:第一,翻新机的重量;第二,翻新机的转速。也就是说,在石材研磨工序中需要重量和低转速;在抛光出亮的工序中,需要低重量和高转速。 花岗岩翻新所需设备、配件及耗材:专业石材翻新机、金属磨片、翻新片、抛光垫、吸水机、告示牌、喷壶、测光仪、玻璃刮、抹水器和水桶。 工作程序及施工方法: ①在工作现场设立告示牌,为防止泥浆污物溅到墙壁,用塑料透明薄膜把地面周围墙壁底部贴好。在石材翻新机水箱里加入清水,接好电源,准备好各型号金属磨片、翻新片等,并调整设备与地面水平,准备工作。如地面有旧蜡则先起蜡。 ②使用50#金属磨片,分别安装在翻新机磨盘上,放水并起动电机研磨。每次研磨1平米左右面积,反复3~5遍,将石材剪口部分研磨至平滑,研磨时水量适中,禁止干磨,用吸水机吸干、吸净地面。 ③更换150#金属磨片、300#金属磨片,按顺序研磨,平整剪口,消除粗糙磨痕。反复研磨,刮洗吸干地面。 ④使用200#、400#、800#进行研磨。 ⑤再使用1500#、3000#抛光片对表面进行抛光,最后将石材表面洗净、吹干,呈现出靓丽的色彩。可根据要求进行晶面处理 Measures for the routine management of moral education in Middle SchoolsMethod of conventional management of moral education in middle schoolFirst, the guiding ideology:School moral education is an organic whole of the whole education work, always adhere to the school adhere to the moral education, education for this product, and actively promote the quality education, the school building efficient curriculum system of moral education, moral education, improve the sense of attraction and appeal, enhance the moral education work for through and timeliness. Teach everyone, service education and management education, and school moral education work must be with family education and community education closely together, to form a concerted pattern, and strive to create a good atmosphere for education, and to promote the all-round development of students, to establish a scientific moral education full of vigor the For long-term mechanism.Two, the goal of moral education:To guide the students to form the correct world outlook, outlook on life, values, to cultivate students unity and mutual assistance, honest and trustworthy, law-abiding, good quality, hard work, set a good XX students ideological quality, psychological qua