道路工程钢筋笼施工方法.docVIP

道路工程钢筋笼施工方法 道路工程钢筋笼施工方法提要：最后施工钢筋笼箍筋，施工箍筋前先在主筋上分出箍筋间距，然后将箍筋缠绕于钢筋笼骨架上并将箍筋与主筋50%交错点焊 道路工程钢筋笼施工方法 钢筋笼制做：该标段钻孔桩设计桩长20m，故钢筋笼整体制做吊装，加工尺寸严格按设计图纸及规范要求，钢筋笼的主筋在地面加长时，接长采用闪光对焊，质量符合设计和规范要求。接头相互错开。主筋与箍筋采用点焊。施工中按照以下规定加工钢筋笼。 先制做钢筋笼的加强箍，加强箍先根据设计长度下料并在特制的平台上弯制而成。加强箍制做完成后，在加强箍上准确的放样出钢筋笼每一根主筋的确切位置并用红油漆做出标记。 主筋分段长度，将所需钢筋用切割机成批切好备用，并按规格挂牌分类堆放整齐。 钢筋笼加工在特制加工平台上进行，加工前先检查平台的平直度，确保钢筋笼的主筋顺直。 加工时先将主筋点焊于加强箍的外侧所标示的主筋位置，确保主筋位置正确，间距一致。 最后施工钢筋笼箍筋，施工箍筋前先在主筋上分出箍筋间距，然后将箍筋缠绕于钢筋笼骨架上并将箍筋与主筋50%交错点焊。 加工成型的钢筋笼稳定放置在坚实平整的地面上，防止变形。 每幅成品钢筋笼须经监理工程师验收，合格后方可使用，每节钢筋笼均要挂牌标识，标明节号、桩号和检验状态。 钢筋笼从上至下每的间距设一道保护块，每道保护块分四块均匀的布置于该圆环上，保护块采用直径100mm的砂浆混凝土块。 （2）钢筋笼吊放：采用20t汽车吊机一次吊放钢筋笼入孔。 钢筋笼均采用滑轮配合3点起吊法，起吊时保持平稳，避免钢筋笼在起吊过程中变形。 下笼时由人工辅助对准孔位，保持钢筋笼垂直、轻放避免钢筋笼碰撞孔壁，下放过程中若遇阻碍立即停止，严禁强行冲放。 Measures for the routine management of moral education in Middle SchoolsMethod of conventional management of moral education in middle schoolFirst, the guiding ideology:School moral education is an organic whole of the whole education work, always adhere to the school adhere to the moral education, education for this product, and actively promote the quality education, the school building efficient curriculum system of moral education, moral education, improve the sense of attraction and appeal, enhance the moral education work for through and timeliness. Teach everyone, service education and management education, and school moral education work must be with family education and community education closely together, to form a concerted pattern, and strive to create a good atmosphere for education, and to promote the all-round development of students, to establish a scientific moral education full of vigor the For long-term mechanism.Two, the goal of moral education:To guide the students to form the correct world outlook, outlook on life, values, to cultivate students unity and mutual assistance, honest and trustworthy, law-abiding, good quality, hard work, set a good XX students ideological quality,