钻井100句.doc

I A D C 100 句 IF HAD ANY QUESTION , PLEASE CORRECT. THANKS! 钻 前 准 备 1、last anchor on rack at 06：00HR 六点最后一个锚上架 2、start of contract at 15：30HR 下午三点半合同开始 3、end of contract at 05：30HR 五点半结束承包合同 4、rig on tow 平台拖航 5、rig arrived well location at 10：00HR 10点平台到达井位 6、run anchors and first anchor on bottom at 11：00HR 抛锚.11点第一个锚到底 7、ballast rig to 70’ draft 压载到70英尺 8、deballast rig 卸载 9、adjust well location with pull No.1 and No.2 anchors gain 拉一、二号锚调整并位 10、anchor tension test No.3 and No.4 OK 锚张力试验.三、四号锚合格 11、wait slack tide 等平潮 12、replace upper kelly cock 替换方钻杆上阀 钻 进 13、spud time 开钻时间 14、arrived time 到达并位时间 15、drill 36” hole from 120m to 200m pump 50BBLS mud each connection and ream each connection once 从120米钻至200米每钻一根打50桶泥浆和扩眼一次 16、open 17 1/2” hole from 250m to 500m 用17 1/2”钻头扩眼 17、leak off test at 500m. MW 1.2sg leak off @ 625psi 破裂实验并深500米比重1.2sg泄漏压力为625 psi 18、ream hole from 450m to 500m 从事50米扩眼到点500米 19、core drill from 1300m to 1320m 取芯钻进从1300米到1320米 20、collect/remove core and service core equipment 回收岩芯及服务工作 21、sweep hole with 100 bbl HI-VIS mud台 清洗并用100桶高粘度泥浆 22、slug the hole with viscous mud 往井中泵入一段稠泥浆 23、pump 6000 STKS HI-VIS mud 打6000冲高粘度泥浆 24、circulate and working on pipe 循环活动钻具 25、circulate and wash hole from 100m to 200m 在100-200米井段循环冲洗 26、circulate bottoms up 循环井底出来 27、circulate for sample 循环取样 28、flow check at 2300m due to drilling break 钻至2300米时突然加快观察 29、circulate for flow check 循环观察 30、circulate and condition mud 循环处理泥浆 31、reverse circulate 反循环 起 下 钻 32、POOH no rotary and no drag 起钻没用钻盘也没拖挂 33、run in W/26” X 36” BHA tag seabed @ 117m 组合36”扩眼及26”领眼钻头上钻探泥面在177米 34、RIH to wipe trip 下钻通井 35、RIH to tag top of cement at 1000m 下钻探水泥面在1000米 36、short trip 0/pull 50klbs 短程起下钻过提50千磅 37、make up new BHA 重新组合下部钻具 38、drop survey pump slug POOH 投测打重泥浆起钻 39、retrieve/return survey 回收测斜仪 40、inside BOP drill at casing shoe 防喷演习在套管鞋 41、POOH circ. fill annulars W/TR.TK.P no good. Suspect mud problems. W/pull out other 5