API 5dp-培训.pptVIP

太仓新宝谊钢管制造有限公司 API 5DP API 5CT API 5L Evaluation only. Created with Aspose.Slides for .NET 3.5 Client Profile 5.2.0.0. Copyright 2004-2011 Aspose Pty Ltd. 培训内容 产生工艺流程---质量控制点 外观检验(检验规范--量具使用) 无损检测(MT ET UT) 螺纹检验 Evaluation only. Created with Aspose.Slides for .NET 3.5 Client Profile 5.2.0.0. Copyright 2004-2011 Aspose Pty Ltd. 生产车间布局 1.热处理车间 2.钻杆车间 3.油套管车间 4.管线管车间 Evaluation only. Created with Aspose.Slides for .NET 3.5 Client Profile 5.2.0.0. Copyright 2004-2011 Aspose Pty Ltd. 一、热处理车间分布加厚线----------------钻杆、油套管 加厚形式 内加厚IU 外加厚EU 内外加厚IEU Evaluation only. Created with Aspose.Slides for .NET 3.5 Client Profile 5.2.0.0. Copyright 2004-2011 Aspose Pty Ltd. 内加厚Miu 内过渡带长度 Liu 内加厚长度 Evaluation only. Created with Aspose.Slides for .NET 3.5 Client Profile 5.2.0.0. Copyright 2004-2011 Aspose Pty Ltd. 外加厚Leu 外加厚长度 Meu 外过渡带长度 Evaluation only. Created with Aspose.Slides for .NET 3.5 Client Profile 5.2.0.0. Copyright 2004-2011 Aspose Pty Ltd. 内外加厚Leu 外加厚长度 Liu 内加厚长度 Meu外过渡带长度Miu 内过渡带长度 Evaluation only. Created with Aspose.Slides for .NET 3.5 Client Profile 5.2.0.0. Copyright 2004-2011 Aspose Pty Ltd. 加厚检验要点: 一、尺寸检验(符合工艺卡要求) 二、外观检验 1.缩径 2.加厚充满状态 3.内过渡带(台阶、凹坑等) 4.模具痕迹 Evaluation only. Created with Aspose.Slides for .NET 3.5 Client Profile 5.2.0.0. Copyright 2004-2011 Aspose Pty Ltd. 一、热处理车间分布热处理------管线管、钻杆、油套管 布局 淬火炉--淬火机床--回火炉--热矫直 控制要点: 1.炉温的选择(包括均匀性) 2.淬火水压大小(内喷、外淋) Evaluation only. Created with Aspose.Slides for .NET 3.5 Client Profile 5.2.0.0. Copyright 2004-2011 Aspose Pty Ltd. 一、热处理车间分布超声波探伤 产品标准: 1.探伤使用标准ASTM E213 2.样管制做:按照产品标准API 5DP,API 5CT,API 5L制作 MAC 职责: 1.设备调试(样管通过漏报、误报为0) 2.检测做好记录,保证设备运行正常 3.与手工人员检测信息沟通 手工 职责: 1.手工设备调试,灵敏度调节合适 2.与MAC及时沟通,复检现场报警管 3.外观检验(加厚外观、管体外观) 4.UT检测:管体、加厚部分 Evaluation only. Created with Aspose.Slides for .NET 3.5 Client Profile 5.2.0.0. Copyright 2004-2011 Aspose Pty Ltd. 一、热处理车间分布精整区 1.管端矫直(检验管端直度) 2.车外圆、内孔 3.磁粉探伤 Evaluation only. Created with Aspose.Slides for .