- 1、本文档共6页,可阅读全部内容。
- 2、原创力文档(book118)网站文档一经付费(服务费),不意味着购买了该文档的版权,仅供个人/单位学习、研究之用,不得用于商业用途,未经授权,严禁复制、发行、汇编、翻译或者网络传播等,侵权必究。
- 3、本站所有内容均由合作方或网友上传,本站不对文档的完整性、权威性及其观点立场正确性做任何保证或承诺!文档内容仅供研究参考,付费前请自行鉴别。如您付费,意味着您自己接受本站规则且自行承担风险,本站不退款、不进行额外附加服务;查看《如何避免下载的几个坑》。如果您已付费下载过本站文档,您可以点击 这里二次下载。
- 4、如文档侵犯商业秘密、侵犯著作权、侵犯人身权等,请点击“版权申诉”(推荐),也可以打举报电话:400-050-0827(电话支持时间:9:00-18:30)。
查看更多
射孔枪弹架管技术要求
弹架管技术要求Technical Requirements for Charge Tube
1. Scope 范围
This technical requirement gives the acceptance / rejection criteria for the following
charge tubes.
本技术要求规定了下列弹架管的接受/拒收标准。
This technical requirement covers as-weld tubing made from cold rolled steel.
本要求规定由冷轧钢板焊接的钢管技术要求。
This technical requirement is only suitable for φ44.45*1.65 and φ49.20*1.65 charge
tube.
本技术要求仅适用于φ44.45*1.65 和 φ49.20*1.65 规格的弹架管。
Serial No. O.D 外径 W.T 壁厚 Grade Single Length End-finished
序号 (mm) (mm) 钢级 单支长度 端部加工
1 44.45 1.65 1010 6705.6 Square cut 切平
2 49.20 1.65 1010 6705.6 Square cut 切平
2. Product Quality Specification 产品质量标准
2.1 General 总体要求
Charge tube manufactured according to this requirement shall conform to latest
edition of ASTM A 513.
按照本要求生产的弹架管应满足ASTM A 513 最新版的要求。
2.2 Chemical Composition Requirements 化学成分要求
Grade Chemical Composition 化学成分 weight 重量%
钢级 C 碳 Mn 锰 P 磷 S 硫
Min Max Min Max Max Max
1010
0.08 0.13 0.30 0.60 0.035 0.035
Note :When manufacturer do chemical composition analysis, apart from what is listed on table,
the rest main chemical elements shall be reported on MTC.
注意:在制造厂做化学成分分析时,除了上表中要求外,还必须在质保书上列出其余主要元
素的含量。
Test frequency 分析频率:
Heat analysis: once per heat.
熔炼分析:每炉一次。
Product analysis: twice per lot.
产品分析:2 次每批。
2.3 Mechanical properties Requirements 机械性能要求
Yield Strength Tensile Strength Elongation
Grade
屈服强度 抗拉强度 伸长率 %
钢级
Min Min
文档评论(0)