南方电网 配网工程 50-PWZDH-01配网变压器监测计量终端安装-作业指导书-2012-.docxVIP

第8部分：配网工程配网变压器监测计量终端安装作业指导书编码：PWZDH-01目次1适用范围······················································································································································3852编写依据······················································································································································3853作业流程图··················································································································································3854安全风险辨析与预控··································································································································3865作业准备························································································································································136作业方法··························································································································································67质量控制措施及检验标准······························································································································91适用范围1.1电压等级35kV及以下配网工程。1.2电气类别配网变压器监测计量终端安装。2编写依据表2编写依据序号引用资料名称1GB50171—1992《电气装置安装工程盘、柜及二次回路结线施工及验收规范》2DL/T5161.1—2002《电气装置安装工程质量检验及评定规程第1部分：通则》DL/T5161.8—2002《电气装置安装工程质量检验及评定规程第8部分：盘、柜及二次回路结线施工质量检验》3Q/CSG10017.2—2007《110kV～500kV送变电工程质量检验及评定标准第2部分：变电电气安装工程》4Q/CSG11105—2008《南方电网工程施工工艺控制规范》5《中国南方电网有限责任公司基建工程质量控制作业标准（WHS）》3作业流程图图3作业流程图4安全风险辨析与预控4.1配网变压器监测计量终端安装前，施工项目部根据该项目作业任务、施工条件，参照《电网建设施工安全基准风险指南》（下简称《指南》）开展针对性安全风险评估工作，形成该任务的风险分析表。4.2按《指南》中与配网变压器监测计量终端安装相关联的《电网建设安全施工作业票》（编码：PWZDH-01-01/01），结合现场实际情况进行差异化分析，确定风险等级，现场技术员填写安全施工作业票，安全员审核，施工负责人签发。4.3施工负责人核对风险控制措施，并在日站班会上对全体作业人员进行安全交底，接受交底的作业人员负责将安全措施落实到各作业任务和步骤中。4.4安全施工作业票由施工负责人现场持有，工作内容、地点不变时可连续使用10天，超过10天须重新办理作业票，在工作完成后上交项目部保存备查。表4.1作业任务安全基准风险指南序号危害名称风险种类风险等级风险控制措施1邻近带电设备施工无安全措施触电中等风险1.严格执行“两票”制度；2.设置安全围栏，挂警示牌；3.禁止擅自扩大工作范围；4.设专人监护2冲击钻作业没有使用个人安全防护用具触电刺伤中等风险按操作规范使用冲击钻，合理使用个人安全防护用品3在湿度较大的环境下不按安全电压等级使用照明灯具触电低风险潮湿季度应先测量空气湿度，并按安全电压要求