【2017年整理】钢结构制图基本规定.pptVIP

Eiffel Towers I and II 钢结构制图基本规定 汉字的 2.3 图样轮廓线以外的尺寸界线，距图样最外轮廓之间的距离不宜小于10mm，平行排列的尺寸线间距宜为7-10mm，并应保持一致. 2.4 总尺寸的尺寸界线应靠近所指部位，中间的分尺寸的尺寸界线可稍短，但其长度应相等. 3. 半径.直径.球的尺寸标注 Evaluation only. Created with Aspose.Slides for .NET 3.5 Client Profile 5.2.0.0. Copyright 2004-2011 Aspose Pty Ltd. 3.1 半径的尺寸线应一端从圆心开始，另一端画箭头指向圆弧.半径数字前应加注半径符号“R”（图1-14）. Evaluation only. Created with Aspose.Slides for .NET 3.5 Client Profile 5.2.0.0. Copyright 2004-2011 Aspose Pty Ltd. 3.2 较小圆弧的半径，可按图1-15形式标注. Evaluation only. Created with Aspose.Slides for .NET 3.5 Client Profile 5.2.0.0. Copyright 2004-2011 Aspose Pty Ltd. 3.3 较大圆弧的半径，可按图1-16形式标注. Evaluation only. Created with Aspose.Slides for .NET 3.5 Client Profile 5.2.0.0. Copyright 2004-2011 Aspose Pty Ltd. 3.4 标注圆的直径尺寸时，直径数字前应加直径符号 %%c“.在圆内标注的尺寸线应通过圆心，两端画箭头指至圆弧（图1-17）. 3.5 较小圆的直径尺寸，可标注在圆外（图1-18）. Evaluation only. Created with Aspose.Slides for .NET 3.5 Client Profile 5.2.0.0. Copyright 2004-2011 Aspose Pty Ltd. Evaluation only. Created with Aspose.Slides for .NET 3.5 Client Profile 5.2.0.0. Copyright 2004-2011 Aspose Pty Ltd. 3.6 标注球的半径尺寸时，应在尺寸前加注符号“ SR”.标注球的直径尺寸时，应在尺寸数字前加注符号 “SФ ”.注写方法与圆弧半径和圆直径的尺寸标注方. Evaluation only. Created with Aspose.Slides for .NET 3.5 Client Profile 5.2.0.0. Copyright 2004-2011 Aspose Pty Ltd. 4. 角度.弧度.弧长的标注 4.1 角度的尺寸线应以圆弧表示.该圆弧的圆心应是该角的顶点，角的两条边为尺寸界线.起止符号应以箭头表示，如没有足够位置画箭头，可用圆点代替，角度数字应按水平方向注写（图1-19）. Evaluation only. Created with Aspose.Slides for .NET 3.5 Client Profile 5.2.0.0. Copyright 2004-2011 Aspose Pty Ltd. 4.2 标注圆弧的弧长时，尺寸线应以与该圆弧同心的圆弧线表示，尺寸界线应垂直于该圆弧的弦，起止符号用箭头表示，弧长数字上方应加注圆弧符号 “⌒ ” （图1-20）. Evaluation only. Created with Aspose.Slides for .NET 3.5 Client Profile 5.2.0.0. Copyright 2004-2011 Aspose Pty Ltd. 4.3 标注圆弧的弦长时，尺寸线应以平行于该弦的直线表示，尺寸界线应垂直于该弦，起止符号用中粗斜短线表示（图1-21）. Evaluation only. Created with Aspose.Slides for .NET 3.5 Client Profile 5.2.0.0. Copyright 2004-2011 Aspose Pty Ltd. 5. 尺寸的简化标注 5.1 桁架简图.杆件的长度等，可直接将尺寸数字沿杆件一侧注写（图1-22）. 5.2 连续排列的等长尺寸，可用 个数X等长尺寸=总长的形式标注（图1-22）. Evaluation only. Created with Aspose.Slides