常用螺纹规范对照表.docVIP

　　·常用螺纹规范对照表 符号?螺纹种类?规范?牙型角?M?公制?粗牙?ISO?261?60°?S?细小螺丝?ISO?R1501?60°?UNC?统一牙?粗牙?ISO?263?60°?UNF?统一牙?细牙?ISO?263?60°?UNEF?统一牙?特细牙?ISO?263?60°?UN?统一牙?固定牙?ISO?263?60°?UNS?统一牙?特殊牙?-----?60°?NC?美制牙?粗牙?ANSI?B1.1?60°?NF?美制牙?细牙?ANSI?B1.1?60°?NEF?美制牙?特细牙?ANSI?B1.1?60°?N?美制牙?固定牙?ANSI?B1.1?60°?NS?美制牙?特殊牙?ANSI?B1.1?60°?BSW?英制牙?粗牙?BS?84?55°?BSF?英制牙?细牙?BS?84?55°?BC?自行车牙?JIS?B0225?60°?SM?针车用?JIS?B0226?60°?CTV?自行行车用风嘴?JIS?D9422?60°?TV?汽车用风嘴?JID?D4207?60°?BSC?英制自行车?BS?811?60°?BA?英制小螺丝?BS?93?30°47°?Tr?公制?爱克母牙?ISO?2902?30°?TW?爱克姆牙?JIS?B0222?29°?ACME?爱克姆牙?ANSI?B1.5?29°?STUB-ACME?浅牙爱克姆?ANSI?B1.8?29°?C?平行管用螺纹?ISO?228/1?55°?BSPF?英制平行管螺纹?BS?2779?55°?PF?英制平行管螺纹?IS?B0202?55°?R?管用?推拔管用?ISO?7/1?55°1/16?Rc?管用?推拔内螺纹?ISO?7/1?55°1/16?Rp?管用?平行内螺纹?ISO?7/1?55°?PT?推拔?管用?JIS?B0203?55°1/16?PS?平行内螺纹?JIS?B0203?55°?BSP?英制管牙?BS?21.2779?55°?NPT?美制一般推拔管用?ANSI?B2.1?60°1/16?NPTR?美制栏杆接头用?ANSI?B2.1?60°1/16?NPS?美制一般平行管用?ANSI?B2.1?60°?NPSM?美制平行管用?装配器用?ANSI?B2.1?60°?NPSL?美制锁紧螺帽用?ANSI?B2.1?60°?NPSH?美制水管用?ANSI?B2.1?60°?NPSC?美制?管接头用?ANSI?B2.1?60°?NH?美制消防水管用?ANSI?B2.1?60°?NPSF?美制干封管用平行内螺纹?ANSI?B2.1?60°?NPTI?美制干封管用平行?ANSI?B2.1?60°?NPTF?美制干封管用推拔?ANSI?B2.1?60°1/16?NGT?美制瓦斯用推拔?ANSI?B57.1?60°1/16?NGS?美制瓦斯用平行?ANSI?B57.1?60°?NGO?美制瓦斯用出口?ANSI?B57.1?60°?SGT?美制瓦斯用特殊?ANSI?B57.1?60°1/8?E?电灯泡用?JIS?C7709?圆?V?瓦斯桶凡而用?JIS?B8245/6?55°3/26?C?薄铜电线管用?JIS?B0204?80°? 常用规格?（公制）? M1.2*0.25?M2.5*0.45?M6*0.75?M10*0.75?M1.4*0.3?M2.6*0.45?M6*1?M10*1?M1.6*0.35?M3*0.5?M7*0.75?M10*1.25?M1.7*0.25?M3*0.6?M7*1?M10*1.5?M1.7*0.35?M3.5*0.6?M8*0.75?M11*1?M1.8*0.35?M4*0.5?M8*1?M11*1.5?M2*0.4?M4*0.7?M8*1.25?12*1?M2.2*0.45?M5*0.5?M9*1?M12*1.25?M2.3*0.45?M5*0.8?M9*1.25?M12*1.5? 常用规格?（美制）?0-80UNF?5-40UNC?10-32UNF?5/16〃-32UNEF?1-64UNC?5-44UNV?12-24UNC?3/8〃-16UNC?1-72UNF?6-32UNC?12-28UNF?3/8〃-24UNF?2-56UNC?6-40UNF?12-32UNEF?3/8〃-32UNEF?2-64UNF?5/32〃-32UNC?1/4〃-20UNC?7/16〃-14UNC?3-48UNC?8-32UNC?1/4〃-28UNF?7/16〃-20UNF?3-56UNF?8-36UNF?1/4〃-32UNEF?7/16〃-28UNEF?4-40UNC?3/16〃-24UNC?5/16〃-18UNC?1/2〃-13UN