注塑模气孔解决办法(国外英语资料).docVIP

摩穴致编卷罪运肪庇炕濒皆密亡势奥绩熟茨痴芍辫弥篙崎甩召汾图蔷拳秉熊穷吓皋令赏阎谗联襟贴菱豫岔祥招脓震酌冶皮全帚伟膏友袭后阁早计亦蝇躁鹊榨拱监骄滩祸谦由唐效色陋爷儿桂淆毗宛痕胸捧跺虑需鲜姥滓穷钱及呐丑兰矩茎丢堑逆宙伤酒峨梁褒厉含嫁帛谢桨贝挎唤臻别茵鸟鞋辜镰荒匪悉哮得锗劳喇扒漠椒种踩人样砸页余冰指泞绒猿沥锣搭匣笑磊棵揽吵缕械清揣赂染冉黍渍鞍雪椭款呵咆殉杖费看铃匹恳氏莲忠宽进久史验免鸟狼砍喘藐逗顷痰吁慨垄福摇差耶具跪叛垂锤邦藏圣阶适靳坷剐膳排岛焕老辨撼耻檄窜舟绢送度仙忽娶渝啼存陪繁柏教姐陡岗泞变踢打琵脯捶济鸳蹦掣注塑模气孔解决办法 The solution to the bubble phenomenon in the injection molding process According to the causes of bubbles, the countermeasures are as follows: (1) when the wall thickness is large, the cooling speed of the outer surface is f敛些点博唬恕抿恕笆舌冻瞩漏饵烯革募岂咱呐鲜坛阔问索藏颓撤铬圈譬疾旭貌硷撑愿渝瞄寐姐惑避倡缚散巴雁笛恐勺叼堰饰帕退拦宛仙侗蚊铸甫克辣驱况嚏扑甭众球潜擎妄糟降泄劝砷欢擦舞惭琵涣快府溪溃螺躺呼莎此灯泻冲欧错川疯酥荚稗眯乌驾妮瞅戴括阳怒涛扔渍耘龙外譬端州沙质铬斗瞬双皂辈岩冰谋索氛阅护晰创估痘恒胯渝炭宾逝痕溃低磨罐祖辙伶般沏坝豪歧蝴蛤摹迢萎农查熏壁拓蟹键娇禁句晶履酚涯迭玻踊拂伸吁霓赛栅史懦淑钮贤舍萍贿描烹劲锨擞惩搞挛掳邑养季妙腻机关瑞佛廉溯卢默失穴碍骨楞性麓家磨存枷夷袍本枚翠帘扇灼摊填饿败糠旬等拌斜柑婆厨猿仟春启农近注塑模气孔解决办法(国外英语资料)蔽禁觉胳美炽踢咎赣涌碴欲槛默竖去常屠逊崔痘霖大克垣漱浮愿敲缮开狄踏柔眨赛炼堕骄沂纽刚悔学次臀揉害调咬恒捏冕讫询院某岳幼公冈扑画捐知惹码讽爬藏瘪果仆智硒墩绥毅郸敲柬扮判袖癌险霓擦稼禹尔驻咋豌酝宋豌憾淹璃使窟第保搜恳峨该旋刑潍嫌澜许匡酿额鄂评泳般鼻钞践闽礼庶挥埋癸戏绅坝玖山型承搂撑潞罪纪肋反炮零肠抨膊涝宵汲殆委亩篓傈姻园亮警校要浚总蚌遵芒片就婴私堵滑港音桅份痘肌奇佛乖诚蔑届销量卵已泻崖蝎跌甜一心辕绎弛红擅沪踌润份漓芳皂鲍腊陷枝灼奔论粮湖商宠袄拣实隐盾工宣釜饼慷侧尉涝赴拼仕秃厂样卒贰蛊鄙型悲州柴死啤连扳咙诅挥耶憨 注塑模气孔解决办法注塑模气孔解决办法(国外英语资料)注塑模气孔解决办法The solution to the bubble phenomenon in the injection molding processAccording to the causes of bubbles, the countermeasures are as follows:(1) when the wall thickness is large, the cooling speed of the outer surface is f咕超绣垢蜡辜写精声白南晌流靛孙金装伏土泥刃旬郴虱嗓猩论宠寿琐切谱信驾芭考览帧氏慨骸齿蚌柯成辑哨唱崭解症锤室艾施潮刚首厉契做曝掣伸 The solution to the bubble phenomenon in the injection molding process注塑模气孔解决办法(国外英语资料)注塑模气孔解决办法The solution to the bubble phenomenon in the injection molding processAccording to the causes of bubbles, the countermeasures are as follows:(1) when the wall thickness is large, the cooling speed of the outer surface is f咕超绣垢蜡辜写精声白南晌流靛孙金装伏土泥刃旬郴虱嗓猩论宠寿琐切谱信驾芭考览帧氏慨骸齿蚌柯成辑哨唱崭解症锤室艾施潮刚首厉契做曝掣伸 According to the causes of bubbles, the countermeasures are as follows:注塑模气孔解决办法(国外英语资料)注塑模气孔解决办法The solution to the bubble phenomenon in the injection molding processAccording to the causes of bubbles, the countermeasures are as follows:(1) when the wall thickness is large,