- 1、本文档共28页,可阅读全部内容。
- 2、原创力文档(book118)网站文档一经付费(服务费),不意味着购买了该文档的版权,仅供个人/单位学习、研究之用,不得用于商业用途,未经授权,严禁复制、发行、汇编、翻译或者网络传播等,侵权必究。
- 3、本站所有内容均由合作方或网友上传,本站不对文档的完整性、权威性及其观点立场正确性做任何保证或承诺!文档内容仅供研究参考,付费前请自行鉴别。如您付费,意味着您自己接受本站规则且自行承担风险,本站不退款、不进行额外附加服务;查看《如何避免下载的几个坑》。如果您已付费下载过本站文档,您可以点击 这里二次下载。
- 4、如文档侵犯商业秘密、侵犯著作权、侵犯人身权等,请点击“版权申诉”(推荐),也可以打举报电话:400-050-0827(电话支持时间:9:00-18:30)。
查看更多
ie现场管理与改善4
Ellipticity of elbow pipes with diameters less than or equal to 150 mm must be not greater than 8% diameter of 200 mm or less shall not be greater than 6%. Wall thickness of the pipe wall thinning rate must not exceed the original 15%. Crease roughness: diameter 125 mm or less, shall not exceed 3 mm diameter less than or equal to 200 mm, not more than 4 mm. 7.3.9 simmering bending production of square steel tube extension, to use the whole tube bending. Interface if necessary, the welding position should be located in the middle of the vertical arm. 7.3.10 install expansion joints should be done. If design is not required, pipe compensator lengthen should conform to the requirements in the following table: square scale length δ x is equal to 1/2. Pre stretch tolerance: casing + 5 mm, +10 mm. 7.3.11 pipe form, location, spacing shall meet the design and specifications. 7.3.12 piping on back or return pipe at higher levels of the upper to automatic valve to install a drain valve below the horizontal parts. 7.3.13 supports and hangers of checks and the number 1) hanger installed must be checked before installation of supports and hangers part models, specifications of springs setting values, whether the materials meet the requirements of drawings and documents; 2) supports and hangers of material, size and accuracy shall conform to the provisions of the design drawings, material technical requirements should be consistent with national standards, industry standards and technical requirements related to the alloy spectrum review should be carried out; 3) pipe supports and hangers part plant product quality certificate for each variable spring supports, constant support hangers, dampers, damper function, there should be factory calibrated test
Ellipticity of elbow pipes with diameters less than or equal to 150 mm must be not greater than 8% diameter of 200 mm or less shall not be greater than 6%. Wall thickness of th
您可能关注的文档
- cpa《风险》第七章 风险管理框架下的内部控制8.doc
- cpa《风险》第六章 公司治理.doc
- cpa《风险》第八章 管理信息系统的应用与管理.doc
- cpa《风险》第五章 风险与风险管理8.doc
- cis企业形象策划2.docx
- cpa《风险》第八章 管理信息系统的应用与管理7.doc
- cpda福建省项目数据分析师授权管理中心.doc
- cpa考试公司战略与风险管理分析公司治理.doc
- cplm物流企业管理试题.doc
- cop检测设备管理程序.doc
- 中国国家标准 GB/T 18233.4-2024信息技术 用户建筑群通用布缆 第4部分:住宅.pdf
- GB/T 18233.4-2024信息技术 用户建筑群通用布缆 第4部分:住宅.pdf
- GB/T 18978.210-2024人-系统交互工效学 第210部分:以人为中心的交互系统设计.pdf
- 《GB/T 18978.210-2024人-系统交互工效学 第210部分:以人为中心的交互系统设计》.pdf
- 中国国家标准 GB/T 18978.210-2024人-系统交互工效学 第210部分:以人为中心的交互系统设计.pdf
- GB/T 16649.2-2024识别卡 集成电路卡 第2部分:带触点的卡 触点的尺寸和位置.pdf
- 《GB/T 16649.2-2024识别卡 集成电路卡 第2部分:带触点的卡 触点的尺寸和位置》.pdf
- 中国国家标准 GB/T 16649.2-2024识别卡 集成电路卡 第2部分:带触点的卡 触点的尺寸和位置.pdf
- GB/T 17889.4-2024梯子 第4部分:铰链梯.pdf
- 《GB/T 17889.4-2024梯子 第4部分:铰链梯》.pdf
文档评论(0)