- 1、本文档共166页,可阅读全部内容。
- 2、原创力文档(book118)网站文档一经付费(服务费),不意味着购买了该文档的版权,仅供个人/单位学习、研究之用,不得用于商业用途,未经授权,严禁复制、发行、汇编、翻译或者网络传播等,侵权必究。
- 3、本站所有内容均由合作方或网友上传,本站不对文档的完整性、权威性及其观点立场正确性做任何保证或承诺!文档内容仅供研究参考,付费前请自行鉴别。如您付费,意味着您自己接受本站规则且自行承担风险,本站不退款、不进行额外附加服务;查看《如何避免下载的几个坑》。如果您已付费下载过本站文档,您可以点击 这里二次下载。
- 4、如文档侵犯商业秘密、侵犯著作权、侵犯人身权等,请点击“版权申诉”(推荐),也可以打举报电话:400-050-0827(电话支持时间:9:00-18:30)。
查看更多
aqwa中文帮助概要1
ANSYS TO AQWA MODEL TRANSLATOR
ANSYS模型文件转换AQWA-LINE标准输入文件
1. INTRODUCTION 引言
It is possible to use classic ANSYS to create an AQWA radiation/diffraction model. Any of the tools available in Workbench or ANSYS can be used to create the model. Once the model is created an AQWA input file can be written out using a macro supplied with ANSYS.
使用传统的ANSYS产生AQWA辐射/绕射模型是可行的。在Workbench或ANSYS中有工具能够建模。一旦模型建立了,使用ANSYS的宏命令ANSTOAQWA可以自动产生AQWA-LINE的输入文件(将.aqwa修改为.dat格式即可)。
2. MODEL DESCRIPTION 模型描述
The model must be meshed with the mesh that you wish to use for the AQWA analysis. If you are working from a model created for a structural analysis, it will probably be necessary to re-mesh the model as the structural mesh is likely to be finer than is need for a diffraction analysis.
必须使用与AQWA中分析单元类型相同的单元来划分模型的网格。如果你的模型建于ANSYS结构分析,可能会需要不断重新划分网格直到网格尺寸、数目等满足绕射分析的要求。
There should be a line of nodes at the waterline, although these nodes do not need to coincide with nodes on the structural model. The translation macro will only make diffracting those elements that are entirely below the waterline. If there are no waterline nodes there will be no diffracting elements at the waterline, which will severely reduce the accuracy of the diffraction analysis.
吃水线上应该有一行节点,尽管这些节点不需要符合结构模型的节点。转换宏会仅仅将位于吃水线以下的单元制作成绕射单元(DIFF)。如果没有吃水线节点,则吃水线上不会有绕射单元,这会严重的减少绕射分析的准确性。
All the panel elements below the water must have their normals pointing outwards.
水下所有的面元必须指示外表面。
In AQWA the vertical axis is always the Z-axis. The translator can convert a model with either Y or Z-axes vertical, but the X-axis must be horizontal and preferably should be along the fore/aft axis of the vessel.
在AQWA中垂向轴总是Z轴。转换器能转换一个以Y或Z为垂直方向的模型,但是X轴必须是水平方向的,最好是沿着船的头/尾轴。
If the structure is symmetric and you wish to use the SYMX or SYMY cards in AQWA, you must only select ? or ? of the model as appropriate. If you model a complete vessel and specify X symmetry, the AQWA model will contain two sets of coincident elements.
如果结构是对称的,你希望
您可能关注的文档
- AOPA无人机训练机构审定规则概要1.doc
- AOP(面向切面编程)概要1.ppt
- 农业区位因素与农业地域类型20160426概要1.ppt
- 农业政策学-导论概要1.ppt
- 农业的区位选择概要1.ppt
- ap statistics 讲课幻灯片概要1.pptx
- 文明之光__彩陶概要1.ppt
- 文明从细节入手概要1.ppt
- 农产品贮藏与加工学整理概要1.doc
- 文明城市测评标准概要1.doc
- 第十一章 电流和电路专题特训二 实物图与电路图的互画 教学设计 2024-2025学年鲁科版物理九年级上册.docx
- 人教版七年级上册信息技术6.3加工音频素材 教学设计.docx
- 5.1自然地理环境的整体性 说课教案 (1).docx
- 4.1 夯实法治基础 教学设计-2023-2024学年统编版九年级道德与法治上册.docx
- 3.1 光的色彩 颜色 电子教案 2023-2024学年苏科版为了八年级上学期.docx
- 小学体育与健康 四年级下册健康教育 教案.docx
- 2024-2025学年初中数学九年级下册北京课改版(2024)教学设计合集.docx
- 2024-2025学年初中科学七年级下册浙教版(2024)教学设计合集.docx
- 2024-2025学年小学信息技术(信息科技)六年级下册浙摄影版(2013)教学设计合集.docx
- 2024-2025学年小学美术二年级下册人美版(常锐伦、欧京海)教学设计合集.docx
文档评论(0)