FDS+EVAC火灾及人员疏散源代码.doc

FDS+Evac version: FDS 6.0.0, Evac 2.4.1 All material properties etc. are completely fabricated. An example shopping centre: two floors with an atrium. HEAD CHID=Atrium, TITLE=FDS Evac demo / Fire mesh: Ground floor dx=0.3125, dy=0.3125 MESH IJK= 128,64,12, XB= 0,40 0,20, 0,4, / Fire mesh: First floor dx=0.3125, dy=0.3125 MESH IJK= 128,64,16, XB= 0,40, 0,20, 4,9, / Fire mesh: Atrium dx=0.3125, dy=0.3125 MESH IJK= 128,27,20, XB= 0,40,0,8.4375, 9,15, / Evac meshes: Ground floor: x=0-40m, y=0-20m, z=1.0m, dx=0.25, dy=0.25 First floor: x=0-40, y=8-20m, z=5.0m, dx=0.25, dy=0.25 MESH IJK= 160,80,1, XB= 0,40, 0,20, 1.0,1.2, EVAC_Z_OFFSET= 1.0, EVACUATION=.TRUE., EVAC_HUMANS=.TRUE., ID = GroundFloor / MESH IJK= 160,50,1, XB= 0,40, 7.5,20, 5.0,5.2,EVAC_Z_OFFSET= 1.0, EVACUATION=.TRUE., EVAC_HUMANS=.TRUE., ID = FirstFloor / TIME T_END =500.0, DT= 0.1 / MISC TMPA=21.0, / Building geometry Ceiling and roof OBST XB = 0, 40, 8, 20, 3.5, 4, SURF_ID = CONCRETE / OBST XB = 0, 40, 8, 20, 8.5, 9, SURF_ID = CONCRETE / The roof of the atrium OBST XB = 0, 40, 0, 8, 13, 13, SURF_ID = GLAZING / HOLE XB = 9, 11, 5, 6, 12.8, 13.2, DEVC_ID=Dev_h1 / HOLE XB = 29, 31, 5, 6, 12.8, 13.2, DEVC_ID=Dev_h2 / DEVC XYZ=0,0,0, ID=Dev_h1, QUANTITY=TIME, SETPOINT=118.0, INITIAL_STATE=.FALSE. / DEVC XYZ=0,0,0, ID=Dev_h2, QUANTITY=TIME, SETPOINT=122.0, INITIAL_STATE=.FALSE. / VENT XB = 0, 40, 0, 8.4375, 15, 15, SURF_ID = OPEN / VENT XB = 0, 40, 0, 0, 13, 15, SURF_ID = OPEN / VENT XB = 0, 40, 8.4375, 8.4375, 13, 15, SURF_ID = OPEN / VENT XB = 0, 0, 0, 8.4375, 13, 15, SURF_ID = OPEN / VENT XB = 40,40, 0, 8.4375, 13, 15, SURF_ID = OPEN / Floor VENT XB = 0, 40, 0, 20, 0, 0, SURF_ID = FLOOR / VENT XB = 0, 40, 8.4375, 20, 4, 4, SURF_ID = FLOOR / Doors VENT XB = 0, 0, 2, 3.2, 0, 2, SURF_ID = OPEN / VENT XB = 40, 40, 2, 3.2, 0, 2, SURF_ID = OPEN / Staircase OBST XB = 16, 20, 6, 8, 0, 9, SURF_ID=GLAZING, RGB= 168,168,168 / Columns O