05 08机咬牙标准调节（008 machine gnashing standard adjustment）.docVIP

下载本文档

2
0
约1.94万字
约 15页
2017-07-15 发布于河南
举报
版权申诉

05 08机咬牙标准调节（008 machine gnashing standard adjustment）.doc

1、原创力文档（book118）网站文档一经付费（服务费），不意味着购买了该文档的版权，仅供个人/单位学习、研究之用，不得用于商业用途，未经授权，严禁复制、发行、汇编、翻译或者网络传播等，侵权必究。。
2、本站所有内容均由合作方或网友上传，本站不对文档的完整性、权威性及其观点立场正确性做任何保证或承诺！文档内容仅供研究参考，付费前请自行鉴别。如您付费，意味着您自己接受本站规则且自行承担风险，本站不退款、不进行额外附加服务；查看《如何避免下载的几个坑》。如果您已付费下载过本站文档，您可以点击这里二次下载。
3、如文档侵犯商业秘密、侵犯著作权、侵犯人身权等，请点击“版权申诉”（推荐），也可以打举报电话：400-050-0827(电话支持时间：9:00-18:30)。
4、该文档为VIP文档，如果想要下载，成为VIP会员后，下载免费。
5、成为VIP后，下载本文档将扣除1次下载权益。下载后，不支持退款、换文档。如有疑问请联系我们。
6、成为VIP后，您将拥有八大权益，权益包括：VIP文档下载权益、阅读免打扰、文档格式转换、高级专利检索、专属身份标志、高级客服、多端互通、版权登记。
7、VIP文档为合作方或网友上传，每下载1次，网站将根据用户上传文档的质量评分、类型等，对文档贡献者给予高额补贴、流量扶持。如果你也想贡献VIP文档。上传文档

05 08机咬牙标准调节（008 machine gnashing standard adjustment）

05 08机咬牙标准调节（008 machine gnashing standard adjustment） The standardization of the grinding teeth of the printing press In the regulation of the press of J2108 and J2205 and use, how to properly adjust the paper teeth and paper teeth to handover location relations with relevant institutions, is a highly technical work. If it is improperly adjusted, it can easily cause a lot of problems such as ruffling, ghosting, tearing and printing. Here is a description of the adjustment of the papers grinding teeth and the analysis of the related failures caused by improper adjustment. It is the regulation of the grinding of the teeth of the paper and the grinding of the cylinder Paper feeding device of the grind and the former rules, roller teeth twice transfer paper, it is in the position of the two transfer paper, should be based on embossing roller teeth, adjust the delivery position paper teeth (or confirm the position has been correctly), to determine the paper teeth in the former gauge sheet position, and then, based on this position again, adjust the gauge before the position of the relevant parts. Figure 01 is the transfer of paper teeth and rollers * pay attention to the order of adjustment when adjusting. Embossing roller teeth is adjust the benchmark of grind, if to gauge before as a benchmark to adjust paper teeth, is easy to cause the whole machines motion transition location of the disorder. The readjustment of the position of the tooth with the press of the paper When the machine is in the 0 position, it is required that the tip of the paper tip be 0.5 ~ 1.5 mm ahead of the cylinder. At this time, the 0 line is tangent to the roller. The gap between the papers pad and the roller cushion is minimized. This position (figure 01) is adjusted before the machine is out of the factory. Machine use for a long time, however, CAM and roller, pin, etc will be wear and tear, this will make the paper and embossing roller transfer position displacement, cause paper teeth knock