HPux系统管理常用方法小结（HPux system management is commonly used in summary）.docVIP

下载本文档

11
0
约 30页
2017-07-15 发布于河南
举报
版权申诉

HPux系统管理常用方法小结（HPux system management is commonly used in summary）.doc

1、本文档共30页，可阅读全部内容。
2、原创力文档（book118）网站文档一经付费（服务费），不意味着购买了该文档的版权，仅供个人/单位学习、研究之用，不得用于商业用途，未经授权，严禁复制、发行、汇编、翻译或者网络传播等，侵权必究。
3、本站所有内容均由合作方或网友上传，本站不对文档的完整性、权威性及其观点立场正确性做任何保证或承诺！文档内容仅供研究参考，付费前请自行鉴别。如您付费，意味着您自己接受本站规则且自行承担风险，本站不退款、不进行额外附加服务；查看《如何避免下载的几个坑》。如果您已付费下载过本站文档，您可以点击这里二次下载。
4、如文档侵犯商业秘密、侵犯著作权、侵犯人身权等，请点击“版权申诉”（推荐），也可以打举报电话：400-050-0827(电话支持时间：9:00-18:30)。
5、该文档为VIP文档，如果想要下载，成为VIP会员后，下载免费。
6、成为VIP后，下载本文档将扣除1次下载权益。下载后，不支持退款、换文档。如有疑问请联系我们。
7、成为VIP后，您将拥有八大权益，权益包括：VIP文档下载权益、阅读免打扰、文档格式转换、高级专利检索、专属身份标志、高级客服、多端互通、版权登记。
8、VIP文档为合作方或网友上传，每下载1次，网站将根据用户上传文档的质量评分、类型等，对文档贡献者给予高额补贴、流量扶持。如果你也想贡献VIP文档。上传文档

HPux系统管理常用方法小结（HPux system management is commonly used in summary）

HPux系统管理常用方法小结（HPux system management is commonly used in summary） Network card address configuration 1. Configure IP address Modify /etc/rc. Config.d/netconf file. INTERFACE_NAME [0] = lan0 # shows the device name of the network card with lanscan IP_ADDRESS [0] = # lan0s IP address SUBNET_NASK [0] = # subnet mask BROADCAST_ADDRESS [0] = # defaults to 55 of the broadcast address INTERFACE_STATE [0] = # boot when you set the nic to up DHCP_ENABLE [0] = 0 # DHCP is started, 0 is not started, 1 is started There are two items in the netconf file that cannot be modified: OPERATING_SYSTEM = HP - UX LOOPBACK_ADDRESS = If you have multiple network CARDS in your server, you can add them at the end of the netconf file INTERFACE_NAME [1] = lan1 IP_ADDRESS [1] = SUBNET_NASK [1] = BROADCAST_ADDRESS [1] = INTERFACE_STATE [1] = DHCP_ENABLE [1] = 0 2. Set the host name of the system The host name of the system has two types: 1. UUCP (UNIX - to - UNIX copy) # uname - S myhpux # sets uucp host name # uname - n # check the uucp host name 2. The Internet host name Hostname myhpux # sets the Internet hostname Check the Internet host name Another way to modify the hostname: Modify /etc/rc. Config.d/netconf file HOSTNAME = myhpux # Internet HOSTNAME Note: HP strongly recommends that the two hostnames be the same. / sbin/init. D /.net SOP; Net start 3. Setup gateway / usr/sbin/route add default 20.08.28.98 1 Automatically add the gateway to the system Vi/etc/rc. Config. D/netconf ROUTE_DESTINATION [0] = default ROUTE_GATEWAY [0] = 20.08.28.98 ROUTE_COUNT [0] = 1 / sbin/init. D/net will execute: / usr/sbin/route add default 20.08.28.98 1 Command netstat -rn to view the routing table You can also use set_parms addl_netwrk to set the default route. The HP UNIX extension partition 1) to enlarge the file system, first to find the logical volume corresponding to the file system, only to expand the logic first To enlarge the file system, volume is given to the file system to expand. 2) to