数控工艺员理论知识（Theoretical knowledge of numerical control technology）.doc

下载文档 降价啦

1
0
约7.47万字
约 19页
2017-07-15 发布于河南
举报
版权申诉
保障服务

数控工艺员理论知识（Theoretical knowledge of numerical control technology）.doc

1、本文档共19页，可阅读全部内容。
2、原创力文档（book118）网站文档一经付费（服务费），不意味着购买了该文档的版权，仅供个人/单位学习、研究之用，不得用于商业用途，未经授权，严禁复制、发行、汇编、翻译或者网络传播等，侵权必究。
3、本站所有内容均由合作方或网友上传，本站不对文档的完整性、权威性及其观点立场正确性做任何保证或承诺！文档内容仅供研究参考，付费前请自行鉴别。如您付费，意味着您自己接受本站规则且自行承担风险，本站不退款、不进行额外附加服务；查看《如何避免下载的几个坑》。如果您已付费下载过本站文档，您可以点击这里二次下载。
4、如文档侵犯商业秘密、侵犯著作权、侵犯人身权等，请点击“版权申诉”（推荐），也可以打举报电话：400-050-0827(电话支持时间：9:00-18:30)。

数控工艺员理论知识（Theoretical knowledge of numerical control technology）

数控工艺员理论知识（Theoretical knowledge of numerical control technology） 2-1 tool material should have the performance 1. Hardness and wear resistance HRC60 above Intensity and resilience Iii. Heat resistance Carbon tool steel red hard about 3000C, high speed steel about 6000C, hard alloy 8000C, 4. Good technology Such as forging, welding, heat treatment, grinding 2-2 high speed steel 1. Ordinary high speed steel Tungsten is a common high speed steel W6Mo5Cr4V2 of tungsten and molybdenum High performance high speed steel 1. High carbon high-speed steel 0.9% ~ 1.05% 2. High-vanadium high speed steel 3. Cobalt high speed steel M42 4. Aluminum high speed steel 3. Powder metallurgy high speed steel 4. Surface treatment of high speed steel 2-3. Hard alloy 1. Type and selection of cemented carbide Tungsten cobalt carbide (YG) YG carbide is not suitable for processing steel materials, because with YG carbide cutting tools cutting temperature is about 6400 c, will be bonded with steel, make the tool produces adhesive wear and tool life YG8: cutter YG6X: special hard cast iron, austenitic stainless steel, heat-resistant alloy, titanium alloy, hard bronze, hard wear resistant insulating material YG10H: high strength steel and heat resistant alloy Tungsten and titanium carbide (YT) : WC + TIC + CO YT5-5TiC %, CO10 %, WC85 %. 900-10000c, suitable for machining steel. But not suitable for processing titanium stainless steel, 3. Tungsten tantalum (niobium) cobalt carbide (YA) WC + TaC + NbC + CO is suitable for semi-finishing processing of cold-hard cast iron, non-ferrous metal and its alloys. It can also be used for semi-finishing and finishing processing of high manganese steel and hardened steel 4. Tungsten titanium tantalum (niobium) cobalt hard alloy (YW) WC + TIC + TaC + NbC + CO applies to steel, cast iron, non-ferrous metal for rough, finish, good versatility Titanium carbide (YN) TiC + Ni + Mo - heat resistant 1100 ~ 13000C, the cutting speed 300 ~ 350m/min apply to steel, cast