制造技术基础试题附答案（The basic test of manufacturing technology is attached）.docVIP

下载本文档

8
0
约1.02万字
约 11页
2017-07-20 发布于河南
举报
版权申诉

制造技术基础试题附答案（The basic test of manufacturing technology is attached）.doc

1、原创力文档（book118）网站文档一经付费（服务费），不意味着购买了该文档的版权，仅供个人/单位学习、研究之用，不得用于商业用途，未经授权，严禁复制、发行、汇编、翻译或者网络传播等，侵权必究。。
2、本站所有内容均由合作方或网友上传，本站不对文档的完整性、权威性及其观点立场正确性做任何保证或承诺！文档内容仅供研究参考，付费前请自行鉴别。如您付费，意味着您自己接受本站规则且自行承担风险，本站不退款、不进行额外附加服务；查看《如何避免下载的几个坑》。如果您已付费下载过本站文档，您可以点击这里二次下载。
3、如文档侵犯商业秘密、侵犯著作权、侵犯人身权等，请点击“版权申诉”（推荐），也可以打举报电话：400-050-0827(电话支持时间：9:00-18:30)。
4、该文档为VIP文档，如果想要下载，成为VIP会员后，下载免费。
5、成为VIP后，下载本文档将扣除1次下载权益。下载后，不支持退款、换文档。如有疑问请联系我们。
6、成为VIP后，您将拥有八大权益，权益包括：VIP文档下载权益、阅读免打扰、文档格式转换、高级专利检索、专属身份标志、高级客服、多端互通、版权登记。
7、VIP文档为合作方或网友上传，每下载1次，网站将根据用户上传文档的质量评分、类型等，对文档贡献者给予高额补贴、流量扶持。如果你也想贡献VIP文档。上传文档

制造技术基础试题附答案（The basic test of manufacturing technology is attached）

制造技术基础试题附答案（The basic test of manufacturing technology is attached） One. Question 15 1. In the cutting process, the feed movement can only have one. (V) 2. The Angle between the main cutting edge and the direction of the movement direction is the main Angle c. (X) 3. The main factor influencing the durability of the tool is the cutting temperature. (X) 4. The cutter Angle increases and the cutting deformation increases. (V) 5. The process is the basic unit of the process. (V) 6. It is not allowed to appear in the positioning scheme of parts. (V) 7. Coarse benchmarks can be used repeatedly in the same dimension. (X) 8. Using six supporting pins to locate the workpiece, the six degrees of freedom of the workpiece are limited. (V) When boring, the edge of boring tool is low, and the vibration resistance is better. (X) 10. The residual compression stress generated by the processing surface layer can improve the fatigue strength of the parts. (V) Two. Choice 15 1. One of the functions of the blade Angle is to control the flow direction of the chip. If the blade Angle is negative, the chip will flow to (A). A. Flow to the processed surface B. Flow to the surface of the processed surface C along the normal direction of the cutting edge 2. In rough machining, the former corner should be taken (); The former corner should be the value of (A) when finishing machining. The more plastic the processing material is, The former Angle should be the value of (); The value of the anterior horn in the processing of brittle materials; The higher the strength, the higher the hardness, the value of the anterior horn. A relatively large B. Relatively small C. Arbitrary 3. The effect of cutting temperature on the cutting temperature is from large to small in order (B). A. Vc, ap, f, b.v. c, f, ap, c. f, ap, vc, ap, f, vc 4. Preparation of machining procedures for parts machinery, preparation of production plans and the most basic unit of cost accounting (D). A. Steps B. Process C. Station