HALAR静电喷涂的工艺步骤（Process steps of HALAR electrostatic spraying）.docVIP

下载本文档

45
0
约9.21千字
约 13页
2017-07-20 发布于河南
举报
版权申诉

HALAR静电喷涂的工艺步骤（Process steps of HALAR electrostatic spraying）.doc

1、原创力文档（book118）网站文档一经付费（服务费），不意味着购买了该文档的版权，仅供个人/单位学习、研究之用，不得用于商业用途，未经授权，严禁复制、发行、汇编、翻译或者网络传播等，侵权必究。。
2、本站所有内容均由合作方或网友上传，本站不对文档的完整性、权威性及其观点立场正确性做任何保证或承诺！文档内容仅供研究参考，付费前请自行鉴别。如您付费，意味着您自己接受本站规则且自行承担风险，本站不退款、不进行额外附加服务；查看《如何避免下载的几个坑》。如果您已付费下载过本站文档，您可以点击这里二次下载。
3、如文档侵犯商业秘密、侵犯著作权、侵犯人身权等，请点击“版权申诉”（推荐），也可以打举报电话：400-050-0827(电话支持时间：9:00-18:30)。
4、该文档为VIP文档，如果想要下载，成为VIP会员后，下载免费。
5、成为VIP后，下载本文档将扣除1次下载权益。下载后，不支持退款、换文档。如有疑问请联系我们。
6、成为VIP后，您将拥有八大权益，权益包括：VIP文档下载权益、阅读免打扰、文档格式转换、高级专利检索、专属身份标志、高级客服、多端互通、版权登记。
7、VIP文档为合作方或网友上传，每下载1次，网站将根据用户上传文档的质量评分、类型等，对文档贡献者给予高额补贴、流量扶持。如果你也想贡献VIP文档。上传文档

HALAR静电喷涂的工艺步骤（Process steps of HALAR electrostatic spraying）

HALAR静电喷涂的工艺步骤（Process steps of HALAR electrostatic spraying） self-collected Feel very useful So upload to baidu Share it with you! Process steps of HALAR electrostatic spraying 1. If necessary Defatting the paint parts Methods including with the appropriate solvent; under the 350-400 ℃ heat treatment for several hours 2. Sand blasting on the surface To remove dirt and make the parts surface rough Remove residual dust with clean, dry compressed air 3. The components are preheated to 260-290 ℃ On the hot part Spray Halar primer with a negative voltage 35-50kv electrostatic spray gun 5. Halar primer melt in the 260-290 ℃ oven The parts need to be in the oven for sufficient time to ensure that the resin is completely melted Prolonged stay at high temperatures increases the likelihood of polymer degradation and flow Remove the parts from the oven On hot parts Spray Halar finish with a negative 30-50kv electrostatic spray gun 7. Halar paint melt in the 260-290 ℃ oven The parts need to be in the oven for sufficient time to ensure that the resin is completely melted Prolonged stay at high temperatures increases the likelihood of polymer degradation and flow 8. Repeat spraying and baking process (6-7) until the desired coating thickness is obtained (according to different parts per layer of spray coating thickness of 150-250um) In the above case Spray 5 to 6 times (a primer + 4/5 level paint) can be coated with 1mm The final coating thickness depends on the use condition and environment of the coated parts Corrosion resistant coatings with extensive anti-chemical properties and anti-permeability properties are required The recommended final thickness is 800-1000um 9. After the last step baking Parts should be cooled in the air It is not recommended to quenching the water in the water or to cool the air with a fan Otherwise, the outer horn coating becomes thinner The inner corner coating shrinkage thickens The use of Halar primer can effectively reduce these problems Advanta