家具五金的质量标准和缺陷术语（Quality standards and defect terminology for furniture hardware）.docVIP

下载本文档

10
0
约1.35万字
约 11页
2017-07-22 发布于河南
举报
版权申诉

家具五金的质量标准和缺陷术语（Quality standards and defect terminology for furniture hardware）.doc

1、原创力文档（book118）网站文档一经付费（服务费），不意味着购买了该文档的版权，仅供个人/单位学习、研究之用，不得用于商业用途，未经授权，严禁复制、发行、汇编、翻译或者网络传播等，侵权必究。。
2、本站所有内容均由合作方或网友上传，本站不对文档的完整性、权威性及其观点立场正确性做任何保证或承诺！文档内容仅供研究参考，付费前请自行鉴别。如您付费，意味着您自己接受本站规则且自行承担风险，本站不退款、不进行额外附加服务；查看《如何避免下载的几个坑》。如果您已付费下载过本站文档，您可以点击这里二次下载。
3、如文档侵犯商业秘密、侵犯著作权、侵犯人身权等，请点击“版权申诉”（推荐），也可以打举报电话：400-050-0827(电话支持时间：9:00-18:30)。
4、该文档为VIP文档，如果想要下载，成为VIP会员后，下载免费。
5、成为VIP后，下载本文档将扣除1次下载权益。下载后，不支持退款、换文档。如有疑问请联系我们。
6、成为VIP后，您将拥有八大权益，权益包括：VIP文档下载权益、阅读免打扰、文档格式转换、高级专利检索、专属身份标志、高级客服、多端互通、版权登记。
7、VIP文档为合作方或网友上传，每下载1次，网站将根据用户上传文档的质量评分、类型等，对文档贡献者给予高额补贴、流量扶持。如果你也想贡献VIP文档。上传文档

家具五金的质量标准和缺陷术语（Quality standards and defect terminology for furniture hardware）

家具五金的质量标准和缺陷术语（Quality standards and defect terminology for furniture hardware） Quality standards and defect terminology for furniture hardware 1. dimensional defects: (1) dimensional tolerance: refers to the actual size of non ferrous metal processing products beyond the standard allowable deviation range. (2) uneven thickness: uneven cross and longitudinal sections of the fingerboard, belt, foil thickness. (3) uneven wall thickness: the thickness of the pipe wall is not uniform on all the cross section of the pipe. (4) elliptical roundness: ellipse refers to the product (round tube, round bar, wire rod, wire rod, etc.), the diameter of the same cross section varies. Roundness is represented by the difference between the largest and smallest diameter of the same cross section. (5) uneven diameter: refers to the diameter of the line, the diameter of the longitudinal range. (6): wave corrugated fingerboard, belt, foil, and wire along the length appears wavy undulating curved surface, the flatness of lost. Waves are unilateral, bilateral, and also appear in the middle of the surface, often in the form of continuous waves and intermittent waves in two ways. (7) split edge: the edge has a continuous or interrupted crack of unequal size. Severe pattern of teeth or interrupted triangles. (8) roll edge: partial edge and edge of edge of plate. Either side or side of the strip is grooved, rolled up or partly raised slightly with the edge. (9) bend: refers to the tube, rod, profiles along the axial (vertical) showing the phenomenon of non flat, sometimes wavy. (10) the side bending: fingerboard, strip and foil along the length direction to the side edge of the bend, a straight line, which is of sickle shape. (11) 8 shape: refers to the wire from the reel to take down, showing disorder, twisted into 8 shape. (12) twist: finger, pipe, edges and corners, profiles and bars are twisted around their longitudinal axis, in a very severe twist or spiral shape. (13) cutting oblique: re