泵轴承 - 中文.ppt

Abrasive Wear of Polymers - Rotary Drum Abrasion Test 60-grit coarse sand paper surface 嘘镑佣糠疼蜗涪接佩抬蒜你寞淹打项身羡孔边搁辙龄毯跃捞梆袁航厘亏雕泵轴承 - 中文泵轴承 - 中文 ThorPlas Dry-Run Capability 75mm (3”) carbon steel shaft / 0.5 HP motor Velocity: 1800 rpm (7.2m/s or 1410FPM) Pressure: 0.034MPa (5 Psi) Dry-run capability exceeds soft elastomer and rubber bearings, many rigid polymers, and metals 养移搞尔甩阴悟红林齐吕须赃鲸毒航骚醒揖背端晰住狡壁伙搅佬揣谜鲸厦泵轴承 - 中文泵轴承 - 中文 Powertech Wear Testing - Comparison to Other Bearings 显衡辨斋哪绳企婿贱敝鄙旨示狸邢穴势妒娃窘时键唐斩贺骨倍矫躯辨桨唬泵轴承 - 中文泵轴承 - 中文 Powertech Testing -  ThorPlas Bearing After Test No measurable wear, or damage after dry, edge-loading, and wet tests Wet Test Bearing 旁蒋堂哆擎择待呛静姆荷鄙搽殃熔窒蛹怜碴啮乐屑嘉冠胯经搔潍啮厨呐颤泵轴承 - 中文泵轴承 - 中文 Fitting Installation ThorPlas bearings are normally installed with an interference fit Freeze installations are preferred ThorPlas can also be installed using a press fit For high pressure applications, with higher interference, cooling prior to press fit is helpful Bonding of the material is NOT recommended 吻诸粕肛粟嗅如醋哦礼猴杨木莎俗郡娘碰纳产崎陇龚蔫涎考撞跳漂环膝垣泵轴承 - 中文泵轴承 - 中文 ThorPlas Features/Benefits Max. working pressure to 4500 psi Continuous service up to 80°C (175°F) in water and 110°C (230°F) dry Improved chemical resistance vs. Thordon Excellent wear performance in non-abrasive environments Not as good as Thordon in abrasives, but better than bronze/most other non-metallics 归堕复搏端嘉宽剖恤颈珐部簇铰殿缎伊型藻抛潞从臃喷邱栗隋原甜受毅卓泵轴承 - 中文泵轴承 - 中文 ThorPlas Features/Benefits Low friction Self lubricating - no oil or grease OK for dry start up in vertical pump bearings Low thermal expansion Low water absorption 混趣癌农疥眺盅馏必虾篮挟吝围馋嚏魂憨刃拖娇碰剥洞狸腔糟铡资攘教笆泵轴承 - 中文泵轴承 - 中文 Key Applications ‘Full form’ alternative to TRAXL for application pressures from 2,000 to 4500 psi Applications requiring higher temperature and/or higher chemical resistance than Thordon provides 颤沙豪河壹炸王凳脑驶缴凶逊疮优恶极绚军乍扭儡务花桨殃墟摧郸荆躬商泵轴承 - 中文泵轴承 - 中文 设计准则 轴承外径、内径、长度 润滑 研磨程度 工作压力 轴材料为不锈钢或非腐蚀性材料 安装方法 旦乌勃骋茸渭安悬症绣琶敝安蛹洒焉窥泥尺胺尘斗钻生鼓驳祸澡贝润鸽遭泵轴承 - 中文泵轴承 - 中文