手机设计规范v4.doc3-28（Mobile phone design standard v4. Doc3-28）.docVIP

下载本文档

4
0
约1.47万字
约 11页
2017-07-26 发布于河南
举报
版权申诉

手机设计规范v4.doc3-28（Mobile phone design standard v4. Doc3-28）.doc

1、原创力文档（book118）网站文档一经付费（服务费），不意味着购买了该文档的版权，仅供个人/单位学习、研究之用，不得用于商业用途，未经授权，严禁复制、发行、汇编、翻译或者网络传播等，侵权必究。。
2、本站所有内容均由合作方或网友上传，本站不对文档的完整性、权威性及其观点立场正确性做任何保证或承诺！文档内容仅供研究参考，付费前请自行鉴别。如您付费，意味着您自己接受本站规则且自行承担风险，本站不退款、不进行额外附加服务；查看《如何避免下载的几个坑》。如果您已付费下载过本站文档，您可以点击这里二次下载。
3、如文档侵犯商业秘密、侵犯著作权、侵犯人身权等，请点击“版权申诉”（推荐），也可以打举报电话：400-050-0827(电话支持时间：9:00-18:30)。
4、该文档为VIP文档，如果想要下载，成为VIP会员后，下载免费。
5、成为VIP后，下载本文档将扣除1次下载权益。下载后，不支持退款、换文档。如有疑问请联系我们。
6、成为VIP后，您将拥有八大权益，权益包括：VIP文档下载权益、阅读免打扰、文档格式转换、高级专利检索、专属身份标志、高级客服、多端互通、版权登记。
7、VIP文档为合作方或网友上传，每下载1次，网站将根据用户上传文档的质量评分、类型等，对文档贡献者给予高额补贴、流量扶持。如果你也想贡献VIP文档。上传文档

手机设计规范v4.doc3-28（Mobile phone design standard v4. Doc3-28）

手机设计规范v4.doc3-28（Mobile phone design standard v4. Doc3-28） This article is contributed by huang_business Doc documents may have a poor browsing experience at the WAP end. It is recommended that you choose TXT, or download the source file to the native view. Mobile phone design benchmark Cell phone thickness analysis chart Flip the top of the mobile phone design: Explanation: 1) the coordination of A and B covers: 0.2mm in the clearance of the decoration line; Graphic: 2) near the axis and the front position best each have two self-contained wire lock and shell (shaft end is a must), the rest of the assembly place by the buckle up and down, left and right sides each 2, the size of the male use 0.6 * 0.7 (high), mother seam allowance and clearance of the male is 0.05 / edge, check the mouth and buckle. 3) the matching clearance between the cutting lens and the shell is 0.07 mm/edge, and the corresponding value of the injection molding lens is 0.1mm. The base surface shall be 0.12 mm back adhesive fixed to the shell, and the peripheral clearance should be reduced by 0.2mm/unilateral, and the space shall be 0.15mm. 4) with the clearance between housing and chrome 0.1 mm/side, bottom stick with glue and shell, if do very hot on the form of fixed, LCD module block must have a grounding copper foil, can use conductive sponge to chrome grounding (opening) on the surface shell. 5) the sea cotton and shell shall be glued together with adhesive, and the single side shall be 0.2mm, and the design of the sponge shall not be less than 1/2 of the thickness of the sponge. The location is: top, bottom screen, camera FPC, SPEAKER, receiver, vibrator, etc., the specifications have a thickness of 1.0, 0.8, 0.5, 0.4, etc. 6) the LCD module is in coordination with the shell: the LCD module is enclosed by the surrounding bone (0.6mm) and can be opened and buttoned in the place where there is a button. The peripheral drawing is 0.5 degree 7) with the hinge and shell: hinge hole on the shel