模具专业英语词汇（Mold professional English vocabulary）.docVIP

下载本文档

39
1
约9.84千字
约 24页
2017-07-26 发布于河南
举报
版权申诉

模具专业英语词汇（Mold professional English vocabulary）.doc

1、原创力文档（book118）网站文档一经付费（服务费），不意味着购买了该文档的版权，仅供个人/单位学习、研究之用，不得用于商业用途，未经授权，严禁复制、发行、汇编、翻译或者网络传播等，侵权必究。。
2、本站所有内容均由合作方或网友上传，本站不对文档的完整性、权威性及其观点立场正确性做任何保证或承诺！文档内容仅供研究参考，付费前请自行鉴别。如您付费，意味着您自己接受本站规则且自行承担风险，本站不退款、不进行额外附加服务；查看《如何避免下载的几个坑》。如果您已付费下载过本站文档，您可以点击这里二次下载。
3、如文档侵犯商业秘密、侵犯著作权、侵犯人身权等，请点击“版权申诉”（推荐），也可以打举报电话：400-050-0827(电话支持时间：9:00-18:30)。
4、该文档为VIP文档，如果想要下载，成为VIP会员后，下载免费。
5、成为VIP后，下载本文档将扣除1次下载权益。下载后，不支持退款、换文档。如有疑问请联系我们。
6、成为VIP后，您将拥有八大权益，权益包括：VIP文档下载权益、阅读免打扰、文档格式转换、高级专利检索、专属身份标志、高级客服、多端互通、版权登记。
7、VIP文档为合作方或网友上传，每下载1次，网站将根据用户上传文档的质量评分、类型等，对文档贡献者给予高额补贴、流量扶持。如果你也想贡献VIP文档。上传文档

模具专业英语词汇（Mold professional English vocabulary）

模具专业英语词汇（Mold professional English vocabulary） 1. Mold professional English Incoming water: gate entry position: gate location Gate type: edge gate Thin water port: pin-point gate size: gate size Turn the water: go runner/gate Nozzle diameter: sprue diameter   Runner: runner Hot runner: hot runner, hot manifold Hot mouth cold runner: hot sprue/cold runner   pumping flow straight shooter: direct sprue gate Round runner: round (full/half runner)   flow computer analysis: mold flow analysis Runner balance: runner balance   hot mouth: hot sprue Hot flow plate: hot manifold   hair heat pipe: cartridge heater Probe: thermocouples   : plug connector plug-in Socket: connector socket   sealing/seal: seal   Three, water: water line Throat: line lpug Throat, tube Plastic tube: plastic tube Quick connector: jiffy quick connector plug/socker   4. Mould parts: mold components Three - plate mould: 3-plate mold 2-plate mold: 2-plate mold   nail/leading edge: leader pin/guide pin Side division/guide sleeve: bushing/guide bushing   in supporting department: shoulder guide bushing Middle toon L: guide pin   thimble board: ejector retainner plate Support plate: support plate   screws, screw Dowel pin   mould slot: the ply bar fabrics Internal mold position: core/cavity inter-lock   thimble, ejector pin Cylinder: ejector sleeve   ejector pin, ejector pin Push plate: stripper plate   shrink ha: movable core, return the core core puller   machine (nylon pull hook) : nylon latch lock Inclined top: lifter   mold (frame) : the mold base Upper module: cavity insert   under internal model: the core insert Row bit (slider) : slide   insert: insert Base/slant chicken: wedge   wear-resistant plate/oil: wedge wear plate Layering: plate   support: the support pillar W: sprue bushing   baffle: stop plate Locating ring: locating ring   lock: latch Buckle chicken: parting lock set   push rod, a push bar Bolt: S.H.S.B   roof: eracuretun Movable arm: