ZB206多功能电池容量测试仪使用说明书V1.2版本ZB206+（ZB206 multi-functional battery capacity tester is used in V1.2 version ZB206 +）.docVIP

下载本文档

42
0
约1.09万字
约 10页
2017-08-04 发布于河南
举报
版权申诉

ZB206多功能电池容量测试仪使用说明书V1.2版本ZB206+（ZB206 multi-functional battery capacity tester is used in V1.2 version ZB206 +）.doc

1、原创力文档（book118）网站文档一经付费（服务费），不意味着购买了该文档的版权，仅供个人/单位学习、研究之用，不得用于商业用途，未经授权，严禁复制、发行、汇编、翻译或者网络传播等，侵权必究。。
2、本站所有内容均由合作方或网友上传，本站不对文档的完整性、权威性及其观点立场正确性做任何保证或承诺！文档内容仅供研究参考，付费前请自行鉴别。如您付费，意味着您自己接受本站规则且自行承担风险，本站不退款、不进行额外附加服务；查看《如何避免下载的几个坑》。如果您已付费下载过本站文档，您可以点击这里二次下载。
3、如文档侵犯商业秘密、侵犯著作权、侵犯人身权等，请点击“版权申诉”（推荐），也可以打举报电话：400-050-0827(电话支持时间：9:00-18:30)。
4、该文档为VIP文档，如果想要下载，成为VIP会员后，下载免费。
5、成为VIP后，下载本文档将扣除1次下载权益。下载后，不支持退款、换文档。如有疑问请联系我们。
6、成为VIP后，您将拥有八大权益，权益包括：VIP文档下载权益、阅读免打扰、文档格式转换、高级专利检索、专属身份标志、高级客服、多端互通、版权登记。
7、VIP文档为合作方或网友上传，每下载1次，网站将根据用户上传文档的质量评分、类型等，对文档贡献者给予高额补贴、流量扶持。如果你也想贡献VIP文档。上传文档

ZB206多功能电池容量测试仪使用说明书V1.2版本ZB206+（ZB206 multi-functional battery capacity tester is used in V1.2 version ZB206 +） Quick hand instructions (by default) : 1. Connect the battery with the battery (or the charger of the charger) to the BAT + and BAT of the blue terminal respectively. The connection line is as short as possible! The tester is connected to 12V Voltage (micro USB power supply is connected to 5V USB power supply), the tester is switched on to display preset current. Press the S - or the + + button to change the preset current within A range of 0.1-2.6 A, and then press the SK button to start the test (for example, the troubleshooting code Err * please refer to the following content), the tester Smart select the battery type and make the termination voltage, the RUN light is lit, and the digital tube display value will be shown from the capacity Ah, energy Wh, voltage V and current A. After the test, RUN The lights go out, showing a quick flicker on Ah and a sound reminder. 3. Press the SK button to stop the flashing alarm, press the S -- or the s+ + button to switch the battery capacity Ah, energy Wh and the discharge platform voltage V Press the SK button, the tester is returned to the boot state, and can repeat the previous operation to test the next battery. Note: once the test is completed, you must perform a keystroke operation, the backup data will be cleaned up, otherwise the backup result will always be saved, even if the power will not be removed! Wrong code Err * meaning and processing method: Err1: the battery voltage is too high, please confirm that the voltage before the battery test is under 8.5 V. Err2: the battery voltage is too low (below the set termination voltage), please confirm the battery voltage and reset the battery. The battery is also displayed Err2. Err3: the battery does not support the set of current or the internal resistance of the circuit is too large. Please use a smaller current test and ensure that the line is thick and sh