ansys单元划分技巧（ANSYS cell partitioning techniques）.docVIP

下载本文档

18
0
约9.78千字
约 7页
2017-08-04 发布于河南
举报
版权申诉

ansys单元划分技巧（ANSYS cell partitioning techniques）.doc

1、原创力文档（book118）网站文档一经付费（服务费），不意味着购买了该文档的版权，仅供个人/单位学习、研究之用，不得用于商业用途，未经授权，严禁复制、发行、汇编、翻译或者网络传播等，侵权必究。。
2、本站所有内容均由合作方或网友上传，本站不对文档的完整性、权威性及其观点立场正确性做任何保证或承诺！文档内容仅供研究参考，付费前请自行鉴别。如您付费，意味着您自己接受本站规则且自行承担风险，本站不退款、不进行额外附加服务；查看《如何避免下载的几个坑》。如果您已付费下载过本站文档，您可以点击这里二次下载。
3、如文档侵犯商业秘密、侵犯著作权、侵犯人身权等，请点击“版权申诉”（推荐），也可以打举报电话：400-050-0827(电话支持时间：9:00-18:30)。
4、该文档为VIP文档，如果想要下载，成为VIP会员后，下载免费。
5、成为VIP后，下载本文档将扣除1次下载权益。下载后，不支持退款、换文档。如有疑问请联系我们。
6、成为VIP后，您将拥有八大权益，权益包括：VIP文档下载权益、阅读免打扰、文档格式转换、高级专利检索、专属身份标志、高级客服、多端互通、版权登记。
7、VIP文档为合作方或网友上传，每下载1次，网站将根据用户上传文档的质量评分、类型等，对文档贡献者给予高额补贴、流量扶持。如果你也想贡献VIP文档。上传文档

ansys单元划分技巧（ANSYS cell partitioning techniques） As we all know, meshing is one of the most critical steps for the finite element analysis. The quality of the mesh directly affects the accuracy and speed of the calculation. In ANSYS, as you all know, there are three steps in mesh generation: defining unit attributes (including real constants), defining mesh attributes on a geometric model, and dividing meshes. Here, we address only a few of the problems involved in this procedure, especially some of the problems associated with complex models. I. free mesh partitioning Free meshing is one of the most automated meshing techniques. It can automatically generate triangular or quadrilateral meshes on surfaces (planes and surfaces), and automatically generate tetrahedral meshes on the body. Usually, can use smart size control technology ANSYS (SMARTSIZE command) to the size and the density distribution automatic control grid, can also be manually set the size of the grid (AESIZE, LESIZE, KESIZE, ESIZE series of command and control) distribution network and selection algorithm (MOPT command). For complex geometric models, the method is time-saving and labor-saving, but the disadvantage is that the number of units is usually large and the computational efficiency is reduced. At the same time, because this method can only generate tetrahedron element for 3D complex model, two order tetrahedron element (unit 92) is recommended to obtain better calculation accuracy. If the choice is hexahedron unit, this method will automatically order hexahedral elements degenerated into consistent tetrahedral elements. Therefore, it is best not to use hexahedral linear (no intermediate nodes, such as No. 45 unit), because the tetrahedron unit of the unit after the degradation of linear, with rigid stiffness, accuracy if the poor; two times using hexahedral elements (such as the No. 95 unit), because it is a degenerate form, the number of nodes and hexahedron prototype unit consistent, just t