eNSP实验：BGP.docxVIP

eNSP实验：BGP组网需求所有路由器均运行BGP协议，Router A和Router B之间建立EBGP连接，Router B和Router C之间建立IBGP连接。要求Router C能够访问Router A直连的8.1.1.0/24网段。配置配置各接口的IP地址（略）PC:8.1.1.2/24RA:#sysn RAinterfaceLoopBack 0ip add 1.1.1.1 32interface e0/0/0ip add 8.1.1.1 24interface s0/0/1ip add 3.1.1.2 24#RB:#sysn RBinterface LoopBack 0ip add 2.2.2.2 32interfaceS0/0/1ip add 3.1.1.1 24interface s0/0/0ip add 9.1.1.1 24#RC:#sysn RCinterface LoopBack 0ip add 3.3.3.3 32interface S0/0/0ip add 9.1.1.2 24#配置IBGP连接为了防止端口状态不稳定引起路由震荡，本举例使用Loopback接口来创建IBGP对等体。使用Loopback接口创建IBGP对等体时，因为Loopback接口不是两对等体实际连接的接口，所以，必须使用peer connect-interface命令将Loopback接口配置为BGP连接的源接口。在AS 65009内部，使用OSPF协议，保证Router B到Router C的Loopback接口路由可达， Router C到Router B的Loopback接口路由可达。配置Router B。#system-viewbgp 65009router-id 2.2.2.2peer 3.3.3.3 as-number 65009peer 3.3.3.3 connect-interface loopback 0#ospf 1area 0network 2.2.2.2 0.0.0.0network 9.1.1.00.0.0.255#配置Router C。#system-viewbgp 65009router-id 3.3.3.3peer 2.2.2.2 as-number 65009peer 2.2.2.2 connect-interface loopback 0#ospf 1area 0network 3.3.3.3 0.0.0.0network 9.1.1.0 0.0.0.255#查看OSPF状态以及Router B到Router C的Loopback接口路由能否可达[RC-ospf-1]dis ospf routing OSPF Process 1 with Router ID 3.3.3.3 Routing Tables Routing for Network Destination Cost Type NextHop AdvRouter Area3.3.3.3/32 0 Stub 3.3.3.3 3.3.3.3 0.0.0.0 9.1.1.0/24 1562 Stub 9.1.1.2 3.3.3.3 0.0.0.0 2.2.2.2/32 1562 Stub 9.1.1.1 2.2.2.2 0.0.0.0 Total Nets: 3 Intra Area: 3 Inter Area: 0 ASE: 0 NSSA: 0 [RC-ospf-1]dis ops[RC-ospf-1]dis osp[RC-ospf-1]dis ospf peer OSPF Process 1 with Router ID 3.3.3.3 Neighbors Area 0.0.0.0 interface 9.1.1.2(Serial0/0/0)s neighbors Router ID: 2.2.2.2 Address: 9.1.1.1 State: Full Mode:Nbr is Slave Priority: 1 DR: None BDR: None MTU: 0 Dead timer due in 28 sec Retrans timer interval: 5 Neighbor is up for 00:02:49 Authentication Sequence: [