Materials Science and Engineering UPRM（材料科学与工程 UPRM）.pdfVIP

下载本文档

31
0
约1.08万字
约 7页
2017-08-06 发布于浙江
举报
版权申诉

Materials Science and Engineering UPRM（材料科学与工程 UPRM）.pdf

1、本文档共7页，可阅读全部内容。
2、原创力文档（book118）网站文档一经付费（服务费），不意味着购买了该文档的版权，仅供个人/单位学习、研究之用，不得用于商业用途，未经授权，严禁复制、发行、汇编、翻译或者网络传播等，侵权必究。
3、本站所有内容均由合作方或网友上传，本站不对文档的完整性、权威性及其观点立场正确性做任何保证或承诺！文档内容仅供研究参考，付费前请自行鉴别。如您付费，意味着您自己接受本站规则且自行承担风险，本站不退款、不进行额外附加服务；查看《如何避免下载的几个坑》。如果您已付费下载过本站文档，您可以点击这里二次下载。
4、如文档侵犯商业秘密、侵犯著作权、侵犯人身权等，请点击“版权申诉”（推荐），也可以打举报电话：400-050-0827(电话支持时间：9:00-18:30)。
5、该文档为VIP文档，如果想要下载，成为VIP会员后，下载免费。
6、成为VIP后，下载本文档将扣除1次下载权益。下载后，不支持退款、换文档。如有疑问请联系我们。
7、成为VIP后，您将拥有八大权益，权益包括：VIP文档下载权益、阅读免打扰、文档格式转换、高级专利检索、专属身份标志、高级客服、多端互通、版权登记。
8、VIP文档为合作方或网友上传，每下载1次，网站将根据用户上传文档的质量评分、类型等，对文档贡献者给予高额补贴、流量扶持。如果你也想贡献VIP文档。上传文档

Materials Science and Engineering UPRM（材料科学与工程 UPRM）

Materials Science and Engineering (INME 4107) 2nd Exam - Home 1. In a new technology for growing FCC single crystals, the growing crystal is pulled in an [110] direction. If the pulling stress is 1MPa; how big will be the resolved shear stress acting in a (111) plane and [10-1] direction? 2. (5 points) A cylindrical rod 120mm long and having a diameter of 15mm is to be deformed using a tensile load of 35000N. It must not experience either plastic deformation or a diameter -2 reduction of more than 0.9x10 mm. Of the materials listed below which are the possible candidates?. Material Modulus of Elasticity (GPa) Yield Strength (MPa) Poisson’s Ratio Al Alloy 70 250 0.33 Ti Alloy 105 850 0.36 Steel Alloy 205 550 0.27 Mg Alloy 45 170 0.20 3. A copper rod 0.25 in. in diameter is to be drawn through a 0.20 in. diameter die in a wire drawing process. Use the graph shown to determine the following: The percentage cold deformation The initial strength required to deform the metal The force required to deform the initial wire is: 4. Using the above graph, suppose we want to reduce a copper plate to a final thickness of 0.1 cm with at least 65000 psi tensile strength, 60000 psi yield strength and 5% elongation. How much cold work is required? Calculate the original plate thickness. The amount of cold work required is between: The original plate thickness must be between: 5. For low concentrations of Zn and Cu, the diffusi