O1 Oil Hardening Tool Steel Buffalo Precision（O1石油硬化工具钢,水牛精度）.pdfVIP

下载本文档

12
0
约3.48千字
约 1页
2017-08-06 发布于浙江
举报
版权申诉

O1 Oil Hardening Tool Steel Buffalo Precision（O1石油硬化工具钢,水牛精度）.pdf

1、本文档共1页，可阅读全部内容。
2、原创力文档（book118）网站文档一经付费（服务费），不意味着购买了该文档的版权，仅供个人/单位学习、研究之用，不得用于商业用途，未经授权，严禁复制、发行、汇编、翻译或者网络传播等，侵权必究。
3、本站所有内容均由合作方或网友上传，本站不对文档的完整性、权威性及其观点立场正确性做任何保证或承诺！文档内容仅供研究参考，付费前请自行鉴别。如您付费，意味着您自己接受本站规则且自行承担风险，本站不退款、不进行额外附加服务；查看《如何避免下载的几个坑》。如果您已付费下载过本站文档，您可以点击这里二次下载。
4、如文档侵犯商业秘密、侵犯著作权、侵犯人身权等，请点击“版权申诉”（推荐），也可以打举报电话：400-050-0827(电话支持时间：9:00-18:30)。
5、该文档为VIP文档，如果想要下载，成为VIP会员后，下载免费。
6、成为VIP后，下载本文档将扣除1次下载权益。下载后，不支持退款、换文档。如有疑问请联系我们。
7、成为VIP后，您将拥有八大权益，权益包括：VIP文档下载权益、阅读免打扰、文档格式转换、高级专利检索、专属身份标志、高级客服、多端互通、版权登记。
8、VIP文档为合作方或网友上传，每下载1次，网站将根据用户上传文档的质量评分、类型等，对文档贡献者给予高额补贴、流量扶持。如果你也想贡献VIP文档。上传文档

O1 Oil Hardening Tool Steel Buffalo Precision（O1石油硬化工具钢,水牛精度）

O1 Oil Hardening Tool Steel Technical Data Sheet O1 Tool Steel is a general purpose oil-hardening tool and die steel. Normal care in heat treatment gives good results in hardening and produces small dimensional changes. O1 has good abrasion resistance and sufficient toughness for a wide variety of tool and die applications. TYPICAL CHEMISTRY : C 0.90 Mn 1.20 V 0.20 W 0.50 Cr 0.50 MACHINABILITY: When properly annealed, O1 has a machinability rating of 90 when compared to a 1% Carbon Steel rated at 100. DIMENSIONAL STABILITY: When oil quenched from the proper hardening temperature, this grade can be expected to expand approximately .0015 in. per in. Note: Distortion (bending, bowing and twisting) and part geometry can add to the variations in movement of a part being hardened. THERMAL CYCLING: In order to avoid decarburization, this grade should be annealed and/or hardened in a controlled neutral atmosphere, vacuum, or neutral salt furnace. 1. Anneal: Heat slowly to 1450° F, soak thoroughly. Cool 25° F per hour to 900° F. Air cool to room temperature. Approximate annealed hardness, 221 Maximum Brinell. 2. Stress Relief of Unhardened Material: Heat slowly to 1250° F. Soak for two hours per inch of thickness at heat. Slow cool (furnace cool if possible) to room temperature. 3. Hardening: a. Preheat: Heat to 1200° F, and hold at this temperature until thoroughly soaked. b. Hardening: Heat to 1475 to 1500° F. Soak at heat for 30 minutes per inch of thickness. c. Quench: Oil quench to 150 to 200° F. Temper immediately. d. Temper: Normally oil hardening steels need to be single tempered only. However, dou