钢结构焊接工艺(The welding process of steel structure).docVIP

钢结构焊接工艺(The welding process of steel structure).doc

  1. 1、本文档共10页,可阅读全部内容。
  2. 2、原创力文档(book118)网站文档一经付费(服务费),不意味着购买了该文档的版权,仅供个人/单位学习、研究之用,不得用于商业用途,未经授权,严禁复制、发行、汇编、翻译或者网络传播等,侵权必究。
  3. 3、本站所有内容均由合作方或网友上传,本站不对文档的完整性、权威性及其观点立场正确性做任何保证或承诺!文档内容仅供研究参考,付费前请自行鉴别。如您付费,意味着您自己接受本站规则且自行承担风险,本站不退款、不进行额外附加服务;查看《如何避免下载的几个坑》。如果您已付费下载过本站文档,您可以点击 这里二次下载
  4. 4、如文档侵犯商业秘密、侵犯著作权、侵犯人身权等,请点击“版权申诉”(推荐),也可以打举报电话:400-050-0827(电话支持时间:9:00-18:30)。
  5. 5、该文档为VIP文档,如果想要下载,成为VIP会员后,下载免费。
  6. 6、成为VIP后,下载本文档将扣除1次下载权益。下载后,不支持退款、换文档。如有疑问请联系我们
  7. 7、成为VIP后,您将拥有八大权益,权益包括:VIP文档下载权益、阅读免打扰、文档格式转换、高级专利检索、专属身份标志、高级客服、多端互通、版权登记。
  8. 8、VIP文档为合作方或网友上传,每下载1次, 网站将根据用户上传文档的质量评分、类型等,对文档贡献者给予高额补贴、流量扶持。如果你也想贡献VIP文档。上传文档
查看更多
钢结构焊接工艺(The welding process of steel structure)

钢结构焊接工艺(The welding process of steel structure) Welding technology measure: 1) welding process test of more use in engineering or joint form representative, to determine the optimum operation method and welding specification, welding technology and welding laboratory test by full charge. 2) assembly positioning welding The A. assembly location before welding, welding groove and oil inside and outside on both sides of the 20mm range must be wiped clean with solvent wipe, and portable grinder grinding impurity removing rust, oxide, the welding base metal surface with metallic luster. B. served as the location of welding work must be certified welder welder. The C. assembly quality meets the technical requirements before the pattern positioning welding (such as the requirement of preheating before welding seam must be preheated to the required temperature only after the positioning welding.) The position of welding, welding rod (should be dried), and the weld wire must be used when welding consumables are consistent, weld positioning should fill the crater. D. weld length is generally 20 - 50mm, 400 - 600mm long distance, leg size should be no more than half of the design size of welds, and should not be greater than 8mm, from the design of positioning welding weld end more than 30mm. (except for special circumstances) E. no weld crack, shall not exceed the standard of slag, porosity and other defects, if there is a welding defect, must be completely removed, re positioning welding. The change of F. in the cross weld and weld direction is not sharp positioning weld, weld positioning should leave the area more than 50mm. 3) the general provisions of welding A. served as the project welder welding must be certified welders, and shall be subject to special training examination (for the training and assessment of the project). B. worked as a welder welding should be familiar with the technical documents of the project and construction technology requirements, and must be i

您可能关注的文档

文档评论(0)

jgx3536 + 关注
实名认证
文档贡献者

该用户很懒,什么也没介绍

版权声明书
用户编号:6111134150000003

1亿VIP精品文档

相关文档