超声波无损探伤技术操作规程1（Ultrasonic non-destructive inspection technology procedures 1）.docVIP

下载本文档

5
0
约1.19万字
约 12页
2017-08-17 发布于河南
举报
版权申诉

超声波无损探伤技术操作规程1（Ultrasonic non-destructive inspection technology procedures 1）.doc

1、原创力文档（book118）网站文档一经付费（服务费），不意味着购买了该文档的版权，仅供个人/单位学习、研究之用，不得用于商业用途，未经授权，严禁复制、发行、汇编、翻译或者网络传播等，侵权必究。。
2、本站所有内容均由合作方或网友上传，本站不对文档的完整性、权威性及其观点立场正确性做任何保证或承诺！文档内容仅供研究参考，付费前请自行鉴别。如您付费，意味着您自己接受本站规则且自行承担风险，本站不退款、不进行额外附加服务；查看《如何避免下载的几个坑》。如果您已付费下载过本站文档，您可以点击这里二次下载。
3、如文档侵犯商业秘密、侵犯著作权、侵犯人身权等，请点击“版权申诉”（推荐），也可以打举报电话：400-050-0827(电话支持时间：9:00-18:30)。
4、该文档为VIP文档，如果想要下载，成为VIP会员后，下载免费。
5、成为VIP后，下载本文档将扣除1次下载权益。下载后，不支持退款、换文档。如有疑问请联系我们。
6、成为VIP后，您将拥有八大权益，权益包括：VIP文档下载权益、阅读免打扰、文档格式转换、高级专利检索、专属身份标志、高级客服、多端互通、版权登记。
7、VIP文档为合作方或网友上传，每下载1次，网站将根据用户上传文档的质量评分、类型等，对文档贡献者给予高额补贴、流量扶持。如果你也想贡献VIP文档。上传文档

超声波无损探伤技术操作规程1（Ultrasonic non-destructive inspection technology procedures 1）

超声波无损探伤技术操作规程1（Ultrasonic non-destructive inspection technology procedures 1） 1 equipment general Shu and main parameters 1.1 device overview URP350, S type ultrasonic detection equipment is using the principle of ultrasonic detection of steel pipe inner surface longitudinal / transverse defects and measurement of wall thickness of steel pipe for a combined non-destructive testing equipment, its main flaw is the host, the steel pipe conveying system and water system composed of Sebei 1.2 main parameters 1.2.1 inspection of steel pipe diameter: 114-273.1mm; 1.2.2 detection of steel pipe wall thickness: 4.8-25mm 1.2.3 steel pipe surface temperature: less than or equal to 80 degrees 1.2.4 tube side blind area length: less than or equal to 200m 2 safety confirmation and inspection 2.1 before operation check all parts of the equipment is normal, confirm the existence of unsafe factors behind the operation 2.2 no more crane operation 3 operation procedure 3.1 boot operation 3.1.1 with more detection of steel tube diameter, choose the appropriate wear-resistant contact boots and installed 3.1.2 mount the support arm to the correct height and tighten the pivot bolt with a wrench 3.1.3 install the counterweight to the correct position and secure it 3.1.4 replace the sleeve ring to the right size and lock it in the right place The squeegee at the 3.1.5 inlet has been replaced to a suitable specification 3.1.6 input the correct pipe diameter of the tube to be inspected on the touch screen 3.1.7 check that the lift has been moved to the correct height 3.1.8 check the calibration device has been moved to the correct height, 3.1.9 check that the pinch roller has been moved to the correct height 3.1.10 pumps the water onto the touch screen, The 3.1.11URP350/S spinning head is either on the line or offline 3.1.12 to ensure that offline calibration devices are compatible with correct specifications and pipe diameters 3.2 turn the rotor before the start of operation The 3.2.1Castell