pcb设计原则和抗干扰措施（PCB design principles and anti interference measures）.docVIP

下载本文档

2
0
约9.35千字
约 8页
2017-08-17 发布于河南
举报
版权申诉

pcb设计原则和抗干扰措施（PCB design principles and anti interference measures）.doc

1、本文档共8页，可阅读全部内容。
2、原创力文档（book118）网站文档一经付费（服务费），不意味着购买了该文档的版权，仅供个人/单位学习、研究之用，不得用于商业用途，未经授权，严禁复制、发行、汇编、翻译或者网络传播等，侵权必究。
3、本站所有内容均由合作方或网友上传，本站不对文档的完整性、权威性及其观点立场正确性做任何保证或承诺！文档内容仅供研究参考，付费前请自行鉴别。如您付费，意味着您自己接受本站规则且自行承担风险，本站不退款、不进行额外附加服务；查看《如何避免下载的几个坑》。如果您已付费下载过本站文档，您可以点击这里二次下载。
4、如文档侵犯商业秘密、侵犯著作权、侵犯人身权等，请点击“版权申诉”（推荐），也可以打举报电话：400-050-0827(电话支持时间：9:00-18:30)。
5、该文档为VIP文档，如果想要下载，成为VIP会员后，下载免费。
6、成为VIP后，下载本文档将扣除1次下载权益。下载后，不支持退款、换文档。如有疑问请联系我们。
7、成为VIP后，您将拥有八大权益，权益包括：VIP文档下载权益、阅读免打扰、文档格式转换、高级专利检索、专属身份标志、高级客服、多端互通、版权登记。
8、VIP文档为合作方或网友上传，每下载1次，网站将根据用户上传文档的质量评分、类型等，对文档贡献者给予高额补贴、流量扶持。如果你也想贡献VIP文档。上传文档

pcb设计原则和抗干扰措施（PCB design principles and anti interference measures）

pcb设计原则和抗干扰措施（PCB design principles and anti interference measures） PCB design principles and anti interference measures.Txt if you love several people at the same time, you are young; if you love only one person, then you are old; if you do not love anyone, you have been reborn. A positive person must have a habit of persistence. PCB design principle and anti-interference measures Printed circuit board (PCB) is a support for circuit components and devices in electronic products. It provides electrical connections between circuit components and devices. With the rapid development of electric technology, the density of PGB is higher and higher. The quality of PCB design has a great impact on the ability to interfere. Therefore, the PCB design must comply with the general principles of PCB design, and should meet the requirements of anti-interference design. General principles of PCB design To make the best performance of electronic circuits, the distribution of components and the layout of wires are very important. For good quality design. The low cost PCB. shall follow the following general principles: 1. layout First of all, to consider the size of Colonel PCB PCB size is too large, the production line is long, impedance increased, decreased ability of anti noise, increased cost; too small, then the heat is not good, and the adjacent lines are susceptible to interference. After determining the size of the PCB, determine the location of the particular element. Finally, according to the functional unit of the circuit, all the components of the circuit are arranged. The following principles shall be observed when determining the location of a particular component: (1) shorten the connection between the high frequency components as much as possible, and try to reduce their distribution parameters and electromagnetic interference between them. Vulnerable components should not be too close to each other, and input and output components should be kept as far away as possi