tcl维修实例逐个记（TCL maintenance examples one by one to remember）.docVIP

下载本文档

2
0
约2.07万字
约 22页
2017-08-17 发布于河南
举报
版权申诉

tcl维修实例逐个记（TCL maintenance examples one by one to remember）.doc

1、原创力文档（book118）网站文档一经付费（服务费），不意味着购买了该文档的版权，仅供个人/单位学习、研究之用，不得用于商业用途，未经授权，严禁复制、发行、汇编、翻译或者网络传播等，侵权必究。。
2、本站所有内容均由合作方或网友上传，本站不对文档的完整性、权威性及其观点立场正确性做任何保证或承诺！文档内容仅供研究参考，付费前请自行鉴别。如您付费，意味着您自己接受本站规则且自行承担风险，本站不退款、不进行额外附加服务；查看《如何避免下载的几个坑》。如果您已付费下载过本站文档，您可以点击这里二次下载。
3、如文档侵犯商业秘密、侵犯著作权、侵犯人身权等，请点击“版权申诉”（推荐），也可以打举报电话：400-050-0827(电话支持时间：9:00-18:30)。
4、该文档为VIP文档，如果想要下载，成为VIP会员后，下载免费。
5、成为VIP后，下载本文档将扣除1次下载权益。下载后，不支持退款、换文档。如有疑问请联系我们。
6、成为VIP后，您将拥有八大权益，权益包括：VIP文档下载权益、阅读免打扰、文档格式转换、高级专利检索、专属身份标志、高级客服、多端互通、版权登记。
7、VIP文档为合作方或网友上传，每下载1次，网站将根据用户上传文档的质量评分、类型等，对文档贡献者给予高额补贴、流量扶持。如果你也想贡献VIP文档。上传文档

tcl维修实例逐个记（TCL maintenance examples one by one to remember）

tcl维修实例逐个记（TCL maintenance examples one by one to remember） TCL maintenance examples one by one to remember TCL rc-c08 sometimes 250V voltage, sometimes suddenly shows the voltage the voltage is lower than 130V automatic shutdown system voltage detection circuit R874 (120K) or C853 (kick off open welding AC----VOL----LOW a bus into the adjustment of the original data of 32 to 15 after it. This seems to be the low voltage detection voltage control point. AC----VOL----HIGH is also a high voltage and low voltage detection control point). TCL2980DB D828 isolation diode 4002 caused the standby 20V normal, two boot protection was 0, with 15K resistance is connected to the pipe coupler measured voltage is not normal. Prescription tcl2918e switch machine 1, +B capacitor and glue 2, R831 (1.5k) is common in the automatic shutdown next to the two elements with sealing glue, you should put it out. 3, R836 R832 4 feet, CPU18 2.5V 5,70V rectifier diode The user said a machine 2918E if you turn off the AC power after a certain period of time it is difficult to start two, a large number of open welding after welding constant practice 30V power output fluctuation, +70 actual 12V fluctuation data cannot replace the boot, +5V wave, measuring the output waveform of AC 400V were normal, normal power supply voltage waveform, STR-F6656 Q801 C waveform in high frequency is too large for C808 200V10UF after the power supply fluctuation still can not boot, a touch or change, change the crystal as usual, measuring 17 feet 12 feet 5V reset voltage, power supply voltage 5V is normal, 18 feet 2.5V normal, rewrite the data after troubleshooting, perhaps even users do not know the machine has been completely damaged, resulting in no doubt data directly. TCL ace NT21228 TV erratic automatic shutdown (in fact, the voltage is too high On observation, found that after a few minutes to boot normally again, but time is shorter, the boot after the TV does not automatically shut down if artificially clos