单级直齿轮课程设计（The design of single stage gear course）.docVIP

下载本文档

1
0
约2.39万字
约 33页
2017-08-18 发布于河南
举报
版权申诉

单级直齿轮课程设计（The design of single stage gear course）.doc

1、本文档共33页，可阅读全部内容。
2、原创力文档（book118）网站文档一经付费（服务费），不意味着购买了该文档的版权，仅供个人/单位学习、研究之用，不得用于商业用途，未经授权，严禁复制、发行、汇编、翻译或者网络传播等，侵权必究。
3、本站所有内容均由合作方或网友上传，本站不对文档的完整性、权威性及其观点立场正确性做任何保证或承诺！文档内容仅供研究参考，付费前请自行鉴别。如您付费，意味着您自己接受本站规则且自行承担风险，本站不退款、不进行额外附加服务；查看《如何避免下载的几个坑》。如果您已付费下载过本站文档，您可以点击这里二次下载。
4、如文档侵犯商业秘密、侵犯著作权、侵犯人身权等，请点击“版权申诉”（推荐），也可以打举报电话：400-050-0827(电话支持时间：9:00-18:30)。
5、该文档为VIP文档，如果想要下载，成为VIP会员后，下载免费。
6、成为VIP后，下载本文档将扣除1次下载权益。下载后，不支持退款、换文档。如有疑问请联系我们。
7、成为VIP后，您将拥有八大权益，权益包括：VIP文档下载权益、阅读免打扰、文档格式转换、高级专利检索、专属身份标志、高级客服、多端互通、版权登记。
8、VIP文档为合作方或网友上传，每下载1次，网站将根据用户上传文档的质量评分、类型等，对文档贡献者给予高额补贴、流量扶持。如果你也想贡献VIP文档。上传文档

单级直齿轮课程设计（The design of single stage gear course）

单级直齿轮课程设计（The design of single stage gear course） I. transmission scheme Second sets of third data: the design of belt conveyor in the first gear reducer (1) working conditions: the service life is 10 years, each year according to 300 days calculation, two shifts system work, the load is steady. (2) original data: cylinder circumferential force F=1.7KN; belt speed V=1.4m/s; Roller diameter D=220mm. kinematic sketch Two, the choice of motor 1 、 motor type and structure type selection: according to the known working requirements and conditions, choose Y series three-phase asynchronous motor. 2, determine the power of the motor: (1) the total efficiency of the transmission: ETA = ETA with total * ETA 2 * * ETA ETA bearing gear coupling * ETA drum =0.96 x 0.992 x 0.97 x 0.99 * 0.95 =0.86 (2) the work power required by the motor: Pd=FV/1000 is the total =1700 * 1.4/1000 * 0.86 =2.76KW 3, determine the motor speed: Working speed of drum shaft: Nw=60 * 1000V/ PI D =60 * 1000 * 1.4/ pi * 220 =121.5r/min According to [2] reasonable transmission table 2. 2 than the recommended range, V belt transmission ratio Iv=2~4, single gear transmission ratio range of Ic=3~5, then a reasonable transmission ratio range of I to i=6~20, the optional range of the motor speed is nd=i * nw= * 121.5=729~2430r/min (6~20) The synchronous speed that meets this range is 960 r/min and 1420r/min. By 8.1 [table 2], three kinds of motor models are found, as follows Motor type, rated power, motor speed (r/min), transmission ratio of transmission KW same turn, full turn, total transmission ratio, with gear 1 Y132s-6 310009607.93 2.63 2 Y100l2-4 31500142011.683 3.89 Considering the size and weight of motor and transmission, the price and the transmission ratio of belt drive and reducer, the two schemes can be seen as follows: scheme 1, due to the low motor speed, larger transmission device and higher price. Program 2 moderate. Therefore, choose motor model Y100l2-4. 4, determine the motor type According t